Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
About kishan
Community Record
20
Posts
1
Kudos
1
Solution
Badges
Apr 21 2022
6:29 PM
I have to inform ISP to assign static IP. After routable ip it works.
... View more
Mar 23 2022
6:12 PM
Hi, We have installed multiple Meraki MX64 for 5 sites and Internet connectivity for all sites connected via 5G and 4G modems. It works fine with other connection which are ISP connection, only issue is between 4G/5G to 4G/5G site to site vpn. Is there any other configuration need to be done on Meraki or 5G modem? Note: It is separate wireless 5G modems with SIM Card in it. Thank you
... View more
Labels:
- Labels:
-
Auto VPN
Dec 14 2021
8:18 PM
you mean I have to configure vlans on MX and also in Switch? What i have done: Configure 2 Vlans in MX. port 1 of MX is connected to Port 24 on Aruba switch (on MX Native vlan 1 and allowed vlans all) Now on Aruba SW i have configured same 2 vlan. Port 24 is tagged. please let me know if i did wrong
... View more
Dec 14 2021
7:08 PM
Hi All, I have MX64 uplink with 4G modem and connected port 1 with Aruba 2930F series switch. I have configured 3 vlans in MX and connected to Aruba switch. configured Native vlan 1 and allowed vlans all on MX. what configuration I need to do in Aruba? or is there any chance i can configure vlan on Aruba instead of MX? please suggest me.
... View more
Jun 29 2021
7:57 PM
Traffic can be sent from Fortigat e to MX but on MX i can not see anything and on Fortigate nothing received from MX. From both end only able to ping PUB IP not LAN subnets, however Tunnel is up @Inderdeep
... View more
Jun 29 2021
5:55 PM
One side is Meraki MX68W and other side is FortiGate. Configured IKE V2 and phase 1&2 both up, tunnel is up. Traffic can be send from fortigate but it received nothing. Checked Private subnets and all configurations, but no luck from Meraki I can able to ping Fortigate's public ip but not lcoal private subnet. From Fortigate he can able to ping my private subnet but not receiving back. anyone able to help or suggest?
... View more
Jun 13 2021
10:01 PM
@DarrenOC Okay will try that one with any spare ports or swap with each other. thank you
... View more
Jun 13 2021
9:53 PM
@DarrenOC Unfortunately there is not any available port I can try but I can check by directly connected on MX and see ethernet port speed where Mr is connected to. I believe its by default 1000Mbps always.
... View more
Jun 13 2021
9:44 PM
I have installed 2 AP directly to MX with Injector in placed same model and same configs on both, bounded to Template. One of them showing 1000mb speed on Ethernet 1 of MR and another one showing only 100mb instead if 1000mb.
... View more
Jun 7 2021
4:42 PM
@ww yes I have allowed any-any to all destination IP for port 7351, and nothing captured in logs regarding this.
... View more
Jun 6 2021
11:45 PM
Both of them, there is second site as well have 2 APs so total 4 APs Thanks
... View more
Jun 6 2021
10:24 PM
when I click on Firewall configuration page, it shows me default rules of Meraki which I have configured already but still showing same error
... View more
Jun 6 2021
10:22 PM
I have placed 2 AP at site which is bounded to the template. It is working fine but sometimes its dropped from the internet. error message: Connection to the Cisco Meraki Cloud is using the backup Cloud connection.
... View more
May 25 2021
6:57 PM
No its not came as a active but as "Ready". Lan connectivity is fine cause primary is works fine.
... View more
May 25 2021
5:05 PM
Its routed mode on MAC address tracking and single LAN configured.
... View more
May 25 2021
4:48 PM
There are two MX65 at site second one is configured as a spare/warm device for device redundancy purpose. Primary is working fine no issue but spare one is keep going unreachable every 30 minutes or an hour then it came online for couple of minutes and went offline again. Troubleshoot done: Checked upstream link, DNS server verified, Note: both of the MX firmware is not up to date yet. Can someone please suggest what troubleshoot steps I need to do?
... View more
May 19 2021
6:45 PM
1 Kudo
yes I have inserted the SIM and after that I have power cycle the MX. So, finally got the solution which is antenna was not plugged in properly.
... View more
May 17 2021
6:29 PM
we have placed new MX67cw to replace old MX and inserted new SIM. wan 1 is active at the moment, but the cellular one is keep in enable state sometimes its trying to connecting but does not get stable mode- "Integrated Ready"
... View more
My Accepted Solutions
| Subject | Views | Posted |
|---|---|---|
| 1276 | Apr 21 2022 6:29 PM |
My Top Kudoed Posts
| Subject | Kudos | Views |
|---|---|---|
| 1 | 1122 |
© 2024 Cisco Systems, Inc.
