Hi there,   I have a question about using the Meraki Mixed Templates with, is it possible to have different Meraki MR models for a unique Template? I mean for a Network managed from a template is it posible to have one MR33 and one MR20? Understanding thatthe MR20 doesn't support the 3rd (2.4 GHz & 5 GHz WIDS/WIPS, spectrum analysis, and location analytics radio) and 4th Radio's (2.4 GHz Bluetooth Low Energy (BLE) radio with beacon and BLE scanning support)   So, the MR20 will do the channel assignment, channel width (Only at 5.0Ghz) and the Radio transmit power range (Tx) automatically like the MR33 in that Branch? Or it need the 3er radio to do that?    Hope you can help me with this.   ... View more

Hello everyone,   I'm    I explain you, I'm working on a PoC (Proof of Concept) to configure an VPN IPSec tunnel between a Meraki MX65 in one site and Checkpoint 600 in a branch office and I'm having some lack of the knowledge in Security VPN topics.   Here's the thing, the Meraki MX65 has a link provided by an ISP and the IP address in the Internet 2 interface never changes (I configure it manually on that interface) and in the other hand, the the Checkpoint 600 it's behind and Internet Modem, the Phase 1 and Phase 2 of the tunnel it's ok, the NAT it's working ok and the PC's in the subnets announced in the VPN can communicate between them.   But, from the Meraki MX, in the VPN config, I'm pointing to the Internet Modem ip public address, this it's not the right thing to do 'cause this IP address can change anytime the ISP (Telmex) wants, even without notifying me obviously because that's not an dedicated link to the branch,   Reading some Meraki MX documentation, I realized that the MX's uses their hostname to make an easy automatic VPN between appliances with "non-provisioning or config required".   my question is, is there a way to point i create a tunnel using a DDNS or a hostname to point to the Checkpoint 600 instead of using and IP address?   Or how can I can solve this, it'd be neccesary another MX appliance?   I share with all of you and network diagram of the PoC:   If you can help me, I'll really appreciate your help.   Regards ... View more

Hi everyone,   I was checking the Meraki MS120-8 Switches and I'm a little bit confused about the MS120-8/8LP versus the MS-120-8P, according to the Datasheet in the What's Included? Section, the MS120-8/8LP comes with 1 x External Power Supply which in turn is composed by 1 x Power Adapter plus 1 x Power Cord, right? but, then I checked out the MS120 Hardware installation guide and in the section MS120-8/LP Series Back Panel I found the following info:                     So it's a little bit confusing, 'cause the hardware installation guide doesn't really specifies if the power cord has to be ordered in spare for those MS120 models   My question here is, Do i have to include the Power Cord in Spare?, or it really comes within the MS120-8/8LP models?   Hope you can help me   Regards     ... View more

Hi everyone, hope you all doing great   I'm planning to connect 2 x Cisco Catalyst 9300-24P-A in VSS that it's a Top of Rack (T.o.R.) in a DataCenter with 2 x Meraki MS425-32-HW in FlexibleStacking through copper or fiber (the client had the final decision depending on the final location of both switches), and then the MS to a ISR 1100, i have these scenarios:   1st Scenario - SFP+ for SMF to Catalyst 9300 and SFP to ISR 1100   Use a pair of SFP+'s for SMF to interconnect both pair of Switches, and then the MS to the ISR 1100 with and SFP, so, does the Cisco SFP's/SFP+'s are compatible with the Meraki SFP's/SFP'+s?   2nd Scenario - Copper Twinax and SFP to ISR 1100   Interconnect both pair of Switches through a pair of Copper Twinax 10GB Cable, and then the MS to the ISR 1100 with and SFP, which brand cable should i use, a Cisco Twinax or Meraki Twinax Cables? and, does the Cisco SFP's/SFP+'s are compatible with the Meraki SFP's/SFP'+s?   3rd Scenario - Copper SFP   Use a pair of SFP+'s for SMF to interconnect both pair of Switches, and the MS to the ISR 1100, so, does the Cisco SFP+'s are compatible with the Meraki SFP's?   Unfonately, i can't find any info about the compatibility between those accessories for this two brands.   Hope you can help me   Regards ... View more