Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
About DavidMCross
Community Record
6
Posts
0
Kudos
0
Solutions
Badges
Mar 31 2022
8:37 AM
Just realised that Im crossing into Class B subnet ranges I think.
... View more
Mar 31 2022
8:31 AM
Thanks for your reply. Kept ranges seperate, ok thanks. Ideally I need a range that includes x.x.170.x so expand it either side. If I change the MX64W out of the way to like x.x.100.x, and then change the Vlan 100 range (where is APs sit) to free up the x.x.171.x range leaving me with a gap of x.x.168.x to x.x.171.x /22 on a 255.255.252.0 subnet? The APs are on static IPs (manually set on each AP rather than reserved in the MX) in the Vlan 100 range on x.x.171.x. Is it as simple as updating the Vlan 100 DHCP range and either changing the static IP to the new range or should I just set then to DHCP on Vlan 100 and I assume the MX will assign an address to them?
... View more
Mar 31 2022
7:38 AM
Hello, We operate an MX84 at the primary site and an MX64W at a secondary site connected via Meraki Site to Site VPN, which was set up prior to my taking over here. We need to increase the DHCP range of address. The current set up is as follows. The MX64W has 2 Vlans with Vlan 1 being 192.168.168.0/24. VLan 2 is 192.168.100.0/24. The MX84 has 7 Vlans, although not all are used currently. Vlan 10 is our primary internal data Vlan with 192.168.170.0/24. Vlan 100 is our MR18 Vlan with 192.168.171.0/24 Vlan 20 is VOIP with 192.168.172.0/24 So I need to increase the available address for Vlan 10, but x.x.171.x is in use. Does that matter if they are all Vlan'd or do the IP ranges have to be kept seperate and clear of each other? If so how do I increase the range without breaking Meraki? I'd rather not have to re-address the entire range and move away from x.x.170.x It would be easier for us to change the MX64W Vlan 1 to another range freeing up the x.x.168.x Regards, David
... View more
Oct 12 2020
10:20 AM
Perfect, thank you. Those were the steps needed to add "Wireless" as an sub-option of the secondary site network, with an exact copy of the primary sites SSIDs. Thanks again.
... View more
Oct 12 2020
6:13 AM
Thanks for your reply but that doesn't work. Inventory allows me to tick the AP in the list, but the "Add to" dropdown is greyed out. Do I need to unclaim it first? I assume I don't loose the device\licence if I do that. If I go to the the Primary Network, select Wireless, tick the AP from the "Access points" Monitor list and clikc the Edit dropdown I now get a "Move to another network" option but the secondary site does not appear an as option to select. I don't know if I need to "remove from network" and\or unclaim first before I can re-assign to the secondary site. Regards, David.
... View more
Oct 12 2020
2:48 AM
Hello All, Not 100% sure this is the right forum but am looking for some advice. I took over an existing Meraki system a year ago so I didn't perform any of the initial setup. We have two physical sites, about half a mile apart, linked via Meraki site to site VPN. Primary site is running an MX84, and they have a large number of MR18 APs. The secondary site is running from a MX64W with an MS switch and they have a third part wifi system. I'd like to move some of the MR18 APs from the Primary site to the secondary, and idealy have a common SSID\Password\Policy set up running across both sites. When I select the Primary site Network there is a Wireless sub-option on the left where all the MR18 APs sit. But there is no Wireless sub-option when I select the secondary site Network. There is a Wireless Network as well as the two sites, but currently that has no APs inside and no other configuration that I can see. At the moment, I cannot "move" existing APs from the primary Network to the seconday Network, but I can to the Wireless Network. Do I need to move these through some other method? Is this due to the secondary site running from an MX64W, or is there a setting\config not in place that means the "Wireless" sub-option isn't available at the secondary site? Pending the above query, do APs that sit in the Wiresless Network operate across all other Networks? If not, do I need to match the SSID\Password\Policy settings between the two networks for clients to connect and operate in both sites? Thanks in advnace, David.
... View more
© 2024 Cisco Systems, Inc.
