Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Register or Sign in
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
About Echopath
Echopath
Here to help
Member since Jun 28, 2020
Jul 6 2020
Community Record
6
Posts
2
Kudos
0
Solutions
Badges
We switched two guns to CAM mode. The battery only lasted 2-3 hours each time, but we did not have the disconnects like we were having. Since I was not onsite, I was unable to test the latency from the gun like I did before which will have to wait until I'm back onsite in a couple weeks. We are also switching an additional gun to CAM mode to broaden our testing. The preliminary test results do seem to indicate that CAM does improve the user's experience.
... View more
@PhilipDAth The latency does seem to be causing issues. The scan guns are running a RDP connection to our ERP software off-premise, so round trip we are often seeing 135-250+ ms avg ping times to the server with ~75-80ms avg response times just getting to the gateway across the wireless network. Again, the connection is all over the place. The users are getting many disconnects/reconnects. Many pauses when they roam from AP to AP within the warehouse, but very low bandwidth utilization on the system. The fact that I have high latency just to the local gateway with the scan guns but no other devices indicates a wireless issue with the scan guns. We have another location using similar hardware connecting to the same server who are not experience issues. Since it is a remote site, its taking some time to get a user to run similar testing for me there as a comparison (pings to gateway for example).
... View more
I did find on a post on the Zebra site https://developer.zebra.com/thread/31921 which suggest CAM only as a troubleshooting method. One post states it as follows: "The only time I have found that CAM mode helps is when the APs do not play well with the power saving schemes on the device. CAM mode is a good test if you are having network issues. If it fixes a problem, it's worth investigating to find out why. There may be some AP settings or firmware updates for the APs or the device that might make power saving mode work properly. I try not to use CAM mode in production unless it is the only way to make things work." I'll enable CAM and test to see if it yields better response times. If so, then I'm back to what the above quote suggests which is Why? Why aren't the scan guns and APs playing well?
... View more
I double check the Wireless LAN Profile setup on the scan guns. Under Battery Usage Mode: there are three options: CAM Fast Power Save MAX Power Save This is the setup in the Fusion software. We have Fast Power Save enabled. You are suggesting that we go to CAM which is "constantly awake mode", correct?
... View more
We went through and disabled all the power saving settings on the device. I can ping from the device and the pings aren't lost, just very high latency. I would think if it was going into power saving mode, then I would start to drop packets or see disassociation from the AP.
... View more
We have a warehouse deployment with 4x MR42 APs. We have the Motorola scan guns isolated to their own SSID running only on 5GHz. All 10 scan guns show very high latency when pinging the local gateway IP on the network. Seeing average latency of 90ms, highest ~200ms, best is 28ms and this is all on the same network. When I put my laptop on the same network, I'm getting 3-5ms pinging the gateway. Latency does not seem to stabilize much when scan guns are near to serving AP. Performed wireless survey of warehouse area. Freqency and power planned to minimize interference, so surveys look good. I'm not seeing much external 5GHz interference. Using 20Mhz channel widths. We were not noticing these issues a few months prior. I have other deployments of similar scan guns running on Meraki with same firmware but model APs. Trying to isolate the issue between a wireless issue or a scan gun hardware/software issue. AP utilization looks to be good. From controller, ping response show similar results as reported above with 0% loss rate. Any suggestions on troubleshooting or isolating the issue would be greatly appreciated.
... View more
My Top Kudoed Posts
© 2024 Cisco Systems, Inc.
