Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
About SGD
SGD
Here to help
Member since Jan 15, 2018
Jan 23 2018
Community Record
11
Posts
0
Kudos
0
Solutions
Badges
Jan 23 2018
7:40 AM
PresITsupport,vlan2 & 3 were only tagged in the vlan port configuration for some ports used in the switch-chain. A serious noob oversight that you solution helped to solve. Thanks again.
... View more
Jan 23 2018
7:32 AM
I'd like to thank everyone's assistance on this, you have been great help, and a valuable resource. I needed to configure each switch-port used in the switch-chain, as I was only configuring half the chain. Everything works great now. Is it ok to accept PresITsupport post as solution, since it outlined basically what I was trying to do? Thanks, again everyone.
... View more
Jan 18 2018
11:23 AM
Sorry guys, we got hit with a winter storm and have been shut down. As soon as we are back in swing I'll check that switch and update my post. Thanks again for all the help you provide.
... View more
Jan 15 2018
1:50 PM
Yes each host can ping the mx from its own subnet and the mx from the other two subnets by inter communication. Chris is starting to convince me it may be my tp switch configuration. I was able to assign taggable ports for vlan2 and vlan3. But I'm locked out from modifying vlan1 from untagged to tagged ports. I'll dive deeper into that issue in the morning to see what the issue might be. Thanks for both your help today. I'll update the thread on the situation as I unravel it. Thanks again.
... View more
Jan 15 2018
1:33 PM
Sorry, very bad very absent minded typo. The correct values I meant to type are as follows. Vlan1 10.0.0.0/24 10.0.0.1 gateway 8.8.8.8 dns Vlan2 10.0.5.0/24 10.0.5.1 gateway 8.8.8.8 dns Vlan3 10.10.0.0/24 10.10.0.1 gateway 8.8.8.8 dns
... View more
Jan 15 2018
12:52 PM
Vlan1 10.0.0.0/24 10.0.0.1 gateway 8.8.8.8 dns Vlan2 10.0.5.0/24 10.0.0.1 gateway 8.8.8.8 dns Vlan3 10.10.0.0/24 10.0.0.1 gateway 8.8.8.8 dns
... View more
Jan 15 2018
12:46 PM
Chris_m, all tp ports are set to trunk but the pvid's are set to 1. Also all ports are set to untagged and unselectable to add tagging. Could this be my problem?
... View more
Jan 15 2018
12:32 PM
PhillipDAth, Bandwidth unlimited, no layer 3 rules, no layer 7 rules, traffic snapping unlimited voip & video conferencing.
... View more
Jan 15 2018
11:30 AM
No group policies affecting any vlans on mx, and yes dhcp is configured for all vlans.
... View more
Jan 15 2018
11:14 AM
Thank you for your reply. Yes, 3 vlans configured on the mx80, and they inter communicate just fine, though only vlan1 has internet access. Mx80 port0/2 (lan1 trunk allow all vlans) -> tp-link switch -> patch bay
... View more
Jan 15 2018
9:04 AM
I have three vlans setup on the mx80, and they intercommunicate just fine. The problem is I only get internet connectivity on vlan1. All Lans communicate through a single mx80 port configured to LAN1 trunk with allow all vlans set. Other than experience, what am i missing here to achieve internet across all vlans while still using a single port configuration? Thanks in advance.
... View more
© 2024 Cisco Systems, Inc.
