Hi,   The docs for port forwarding states: "When mapping a range of public ports to a range of local ports, the ranges must be the same length. (ie, 8000-8500 public must be mapped to 8000-8500 local)"   However the UI allows me to configured: Usually, the UI is very good at not allowing you to configured things that are not allowed. Is this normal? I have different lengths in the port ranges which the docs says must be the same.   Thanks, -Jerome ... View more

Hi,   I have a question regarding a value being returned by the following API: GET 'https://api.meraki.com/api/v1/networks/{networkId}/appliance/firewall/portForwardingRules' the attribute "uplink" returns 3 different values "both", "internet1", or "internet2". Can I assume that this maps to the uplink API: GET 'https://api.meraki.com/api/v0/networks/{networkId}/devices/{serial}/uplink' to the "interface" attribute:  "interface": "WAN 1" so from the port forwarding API "internet1" maps to "WAN 1" and "internet2" maps to "WAN 2" on the device?   Thanks in advance, -Jerome ... View more

Hi,   Is routing defined on a switch when an L3 interfaces is configured? This doc: https://documentation.meraki.com/MS/Layer_3_Switching/MS_Layer_3_Switching_and_Routing#Configuring_Static_Routes states that once an L3 interface is configured that routing is enabled. However, it also states: "Only VLANs with a routed interface configured will be able to route traffic locally on the switch, and only if clients/devices on the VLAN are configured to use the switch's routed interface IP address as their gateway or next hop." What is meant by "locally"? Is this routing only referring to inter-vlan traffic?   Thanks in advance, -Jerome ... View more

H,   In reading this doc: https://documentation.meraki.com/MS/Other_Topics/Switch_ACL_Operation   It's not clear to me how these ACLs are applied. I'm assuming this is all L3 traffic - so are the ACL applied on all ports? If so, is it only applied when an L3 interface is created. It states that "Any traffic passing through the switch will be evaluated. Even traffic that is not routed." Passing in which direction (outbound or inbound)?   Thanks in advance, -Jerome     ... View more

Hi,   In this doc: https://documentation.meraki.com/MS/Layer_3_Switching/MS_Layer_3_Switching_and_Routing#Configuring_Static_Routes it specifies that you can configure a Layer 3 interface. When this interface is configured. Will it show up when I use the following API call: GET 'https://api.meraki.com/api/v0/networks/{networkId}/devices/{serial}/uplink Or is there another API that will get me that info?   Thanks in adv ... View more

Hi,   I have an app that gets access rules, interface data form MX devices. I'm looking at the API docs for support on the Z-series devices. I don't see any APIs for getting access-rules, VPN, VLANs, etc.. similar to the MX. Since the Z-series are Firewalls, will the MX specific APIs work for the Z-series?   Thank you, -Jerome ... View more

Hi,   There's 2 APIs under "Organizations": GET 'https://api.meraki.com/api/v0/organizations/{organizationId}/deviceStatuses' GET 'https://api.meraki.com/api/v0/organizations/{organizationId}/inventory'  WIll both return all the devices being managed by the dashboard (i.e. all the devices under all networks)? With the difference in 'deviceStatues' providing if the device is "Active"? ... View more

Hi,   I notice there's an API for getting inbound filters on an MX device:     GET 'https://api.meraki.com/api/v0/networks/{networkId}/appliance/firewall/inboundFirewallRules' Successful HTTP Status: 200 { "rules": [ { "comment": "Allow TCP traffic to subnet with HTTP servers.", "policy": "allow", "protocol": "tcp", "destPort": 443, "destCidr": "192.168.1.0/24", "srcPort": "Any", "srcCidr": "Any", "syslogEnabled": false } ], "syslogDefaultRule": true }       However, I can't find where on the dashboard to configure this. There's a Note on the firewall page that says: Inbound rules Inbound traffic will be restricted to the services and forwarding rules configured below.   But the forwarding rules does not look like the output above. Is there another section where this is configured?   Thanks, -Jerome ... View more