Meraki

Dena · ‎Oct 30 2019

And what if I created 2 dhcp servers (one for LAN (192.168.1.0/24 and one for Camera 192.168.9.0/24) on MX. Then I have to open a port for NVR on MX, right? I am not sure the same port I have to open on the router also but for which IP? For the wan IP of the meraki? Am I correct? Thank you again, Denisa

Dena · ‎Oct 30 2019

I see. Thank you for sharing your experience. I have configured a MX this way on a small business, before a month ago. It looks good. But the meraki representative here at my place advised me to configure the router as bridge and to configure the pppoe on MX. And I have this feeling like Meraki would not able to filter well the traffic. Thank you, Densia

Dena · ‎Oct 30 2019

Hello, I have a question that is not clear to me. Related the connection on the network of the MX. If I connect the MX after a router (the one that face the ISP), where I have configured a DHCP server. And Meraki MX is connected like DHCP client. Would this be a problem for the meraki MX to function properly? Thank you, Denisa

Dena · ‎Oct 24 2019

Hi Hitoshi, :)' my bad, I didn't notice the interface selection was Internet. However I cannot understand a lot from the packet-capture. There are all the time arp packets between meraki and this linux device Shenzhen Bilian. Then came up this IP 192.168.16.104 😕 Thank you for your help, Kind Regards, Denisa

Dena · ‎Oct 23 2019

Hi Hitoshi, I did performed ping as you advice me (although I can see that the device is doing traffic). I cannot capture nothing from any client devices. The only captured traffic is of the routerboard that face the ISP (LAN-Meraki-Routerboard-ISP). Thank you, Denisa

Dena · ‎Oct 22 2019

Hi hintoshi, Thank you for your advice. yes I have tried to sniff the packed but nothing is captured for this device. Kind regards, Dena

Dena · ‎Oct 22 2019

No it was not segmented before.

Dena · ‎Oct 22 2019

Yes I can see it, is receiving Ip 192.168.1.15. But the event keep showing again. I will try to check that device closer. Thank you

Dena · ‎Oct 22 2019

VLAN 10 (192.168.1.0/24) is the only vlan for all the devices. I have installed the MX a couple days ago. I didn't segmented the network. Well I think is a static IP configured but in the same range (192.168.1.0/24). It seems strange that on the event, it shows : last_illegal_ip 192.168.16.103

Dena · ‎Oct 22 2019

Hello All, I am getting a lot of events: "Source IP and/or VLAN mismatch" from one device (I think is a camera). source_client_ip: 192.168.1.15, source_client_mac: 28:F3:66:AC:C2:83, source_client_assigned_vlan: 10 « hide last_illegal_ip 192.168.16.106 client_total_illegal_packets 19828 all_total_illegal_packets 20942 last_reported_total 20906 I dont understand why! Anyone have any idea? Thank you, Dena

Meraki

Community

About Dena

Dena

Community Record

Badges

Re: ISP-Router-MX64 _ MX take IP from DHCP of the router!

Re: ISP-Router-MX64 _ MX take IP from DHCP of the router!

ISP-Router-MX64 _ MX take IP from DHCP of the router!

Re: Source IP and/or VLAN mismatch-Meraki MX-64!

Re: Source IP and/or VLAN mismatch-Meraki MX-64!

Re: Source IP and/or VLAN mismatch-Meraki MX-64!

Re: Source IP and/or VLAN mismatch-Meraki MX-64!

Re: Source IP and/or VLAN mismatch-Meraki MX-64!

Re: Source IP and/or VLAN mismatch-Meraki MX-64!

Source IP and/or VLAN mismatch-Meraki MX-64!

Re: Source IP and/or VLAN mismatch-Meraki MX-64!