Hi,   You can change the DHCP option for all your client devices behind this MX to have Umbrella DNS.   MX DNS setting will only affect the management traffic to Meraki. ... View more

Hi,   I believe content filtering gets lower priority than the firewall L3/L7 rules.   Check this documentation.    https://documentation.meraki.com/MX/Content_Filtering_and_Threat_Protection/Content_Filtering_Rule_Priority ... View more

Hi,   Basically, on MX you should set a static route for all internal networks to point to the internal L3 switch.   On the internal switch side, you should set a static route for the client VPN subnet to point to the MX IP.   In this way, you could have two-way traffic between client VPN subnet and the internal subnet. ... View more

Hi,   So you are able to list the admin and organization via API but no others like listing networks or any update queries?   What is your account's permission? Org full admin? ... View more

Hi,   Can you make sure you are using the correct API key?   You may need to revoke the current one and generate another one. ... View more

Hi,   Did you enable access to the Dashboard API?     This can be found in Organization -> Setting -> Dashboard API access.       ... View more

Hi,   So if you have the VPN subnet as 10.10.200.0/24 on Meraki device in passthrough mode. Then the subnet 10.10.200.0/24 will follow the default route which is the default GW for this MX. This is because the MX is in passthrough mode. Therefore the GW device of MX has to know how to reach this VPN subnet and how to reach the internal network as well.  ... View more

Hi,   Just want to check how you control the Azure side to pass the traffic back to MX1 or MX2 when both tunnels are connected. The MXes are in HA mode so only one MX is actually passing the traffic. ... View more

Hi,   For your topology, I believe it's better to set up the MX as routed mode since you have connected the MX WAN to the public LAN side which should not have access to internal LAN.   Did you change the WAN IP on the MX84 connecting as routed mode and passthrough mode?   If not both modes the client VPN should be able to connect, you may need to check the upstream firewall to make sure the UDP 500 and 4500 been allowed on upstream ISP to your MX WAN IP.   If the client is connected but unable to reach the resource, for passthrough mode, you will need to make sure the WAN GW got the route pointing to the client VPN subnet on MX and is able to route it to your internal network. For routed mode, you will need to set up a new VLAN on MX to connect to your internal switch since the client VPN will set up a separate VLAN on MX and then configure a static route on both MX and your internal switch to allow the VPN subnet to be routed.            ... View more

Hi,   Yes, you can purchase the Cisco contract to extend the warranty of the outdoor Meraki AP and this is called Meraki Now. You can actually contact your Meraki AM and check for Meraki Now. Thanks! ... View more

Hi,   I am able to view the video wall rotation with access "View live footage" and "All cameras in this network".   So I believe this is the most restrict admin privilege on a camera network if you want to see all cameras.    But I will need to start the video wall rotation once I have logged into the "video wall" in my camera network.     Best Regards Chris        ... View more

Hi,   I don't believe there is documentation explicitly saying how often this info will be updated.   Basically, the time is depending on how often the Dashboard query the switch port for this info and updated for API query since API only query the Dashboard.   It may be worth sending a feature request regarding your issue. Thanks!     Best Regards, Chris ... View more

Hi,   I believe you will need to perform the API query to get the network ID and the Bluetooth client ID first.   Try below to retrieve the network ID and Bluetooth client ID. And you can find these in API doc.   https://api.meraki.com/api/v0   https://api.meraki.com/api/v0/organizations/{organizationId}/networks   https://api.meraki.com/api/v0/networks/{networkId}/bluetoothClients       Best Regards, Chris ... View more

Hi ,   I think you design may not work. MX HA will share all the configurations between the primary and secondary, so any VPN set up on the MX HA will apply to both MXes. So you will have both VPN peers on both MX. For non-Meraki VPNs, I don't believe they will have tracking function to failover between two Non-Meraki VPN peers.     Best Regards, Chris ... View more

@Stealth_Network    I think you may need to contact the support since they may have more visibility on which sessions are affected by the firewall rules on the Meraki device.  ... View more

Hector,   I believe this is a known bug with RF manual setting.   But it's better to open a case with support to confirm.     Regards,   Chris ... View more