Meraki

CWMARS · ‎Aug 13 2024

Thanks for the response, this is a public library built in 1886 so we will test and see what's in these walls!

CWMARS · ‎Aug 13 2024

Thanks for the response, this is a public library built in 1886 so we will test and see what's in these walls!

CWMARS · ‎Aug 12 2024

I have an issue with a historical building that needs outdoor wireless coverage. We cannot hang the MR86 on the outside of the building due to its historical architecture. Can an MR86 mounted on a wall inside of the building with (2) MA-ANT-25 pointing out get coverage through a brick exterior? I haven't been onsite to test but wondered if it is worth trying.

CWMARS · ‎Feb 8 2023

If you click the Give Feedback button on the bottom of the appliance status screen you can submit a change request. Thanks, Anne

CWMARS · ‎Jun 23 2022

I've requested many times on the wish list the addition of port descriptions which would be beneficial when troubleshooting devices connected directly in these MX ports.

CWMARS · ‎May 19 2020

Hi, We are a library network and I advise our libraries to run a summary report on the public hotspot SSID monthly and have it emailed. They then just plug it into a spreadsheet for their annual ARIS report. We use a splash page to protect the library from liability for copyrighted materials being downloaded on the public wireless device. In the summary report the accurate number would be the devices granted access by actually accepting the splash page. The number of devices otherwise could be just devices connecting but not actually accepting the page and using the internet. Hope this helps! Anne CW MARS bark.cwmars.org

CWMARS · ‎Apr 29 2020

Done! Thanks!

CWMARS · ‎Dec 11 2019

Dear Meraki, I can't begin to tell you how frustrating it is that I can see what port a device is connected to and have a port description in a Meraki MS switch but cannot add a description or see in connected clients any port information on devices connected to MX ports!! This is frustrating at remote sites when a cable is moved and you have VLANs configured and no way to tell what port it's connected to??? Even just a mac address table identifying the port would be helpful in the MX's!! Ok. That's my Christmas wish ☃️☃️

CWMARS · ‎Sep 13 2019

Thanks Nolan!

CWMARS · ‎Sep 13 2019

Hi Everyone, We try and monitor the OS of the devices on our networks since we no longer support MS Windows 7 and are trying to get our users to upgrade. In checking the OS info we have found that the info listing on the network-wide clients in the MS120 switches usually states "other" whereas the MX security device states that it is "Windows 10". Why would these two devices communicating with each other interpret the same device differently? What's the point of the OS info in the MS120 if it just says "other"? Thanks, Anne

CWMARS · ‎Sep 12 2019

A bit about yourself & your work I am part of the largest library network in Massachusetts - CW MARS, I help support a network of 150+ library locations. Your experience with Cisco Meraki We have been slowly migrating our library sites to all Cisco Meraki MX, MR and MS products. A fun fact about yourself I've been working in IT for about 25+ years and am originally from California but traded in the sunshine for nice cold winters in Massachusetts!!

Meraki

Community

About CWMARS

CWMARS

Anne Savoie

Community Record

Badges

Re: MR86 w/MA-ANT-25 range

Re: MR86 w/MA-ANT-25 range

MR86 w/MA-ANT-25 range

Re: New in MX, where are the port configs and descriptions?

Re: New in MX, where are the port configs and descriptions?

Re: How to Capture Wireless Sessions

Re: Share your feedback and snag some swag!

Re: A Guest Community Challenge!

Re: OS information not matching

OS information not matching

Re: Welcome! Please introduce yourself.

Re: Welcome! Please introduce yourself.

Re: MR86 w/MA-ANT-25 range

Re: New in MX, where are the port configs and descriptions?

Re: New in MX, where are the port configs and descriptions?

Re: A Guest Community Challenge!