Meraki

Community

About Dan_Andolsen

WPA2 PSK with MAC Address Filter

by in Wireless
‎Aug 16 2019 10:47 AM
‎Aug 16 2019 10:47 AM
I have read through the Meraki's AP configuration guide about MAC address filtering, and see that it only support via "Association requirements" with "no encryption."   In non-Meraki, Cisco-based Wi-Fi infrastructure, you can use both WPA2 encrypted data and MAC Address filtering.   Does Meraki support Wi-Fi encrypted data configuration and MAC Address filtering?   Thanks   ... View more

Re: Wi-Fi clients not obtaning DHCP Address

by in Wireless
‎Aug 16 2019 9:31 AM
‎Aug 16 2019 9:31 AM
Move the native cisco cli command to a different VLAN that will not be used in "VLAN Tagging" worked.   Thanks PhilipDAth, and all other for the helpful replies. ... View more

Re: Wi-Fi clients not obtaning DHCP Address

by in Wireless
‎Aug 9 2019 1:24 PM
‎Aug 9 2019 1:24 PM
I get it, the access point should not be in the same VLAN as any tagged VLANs listed in a SSID.   I will try that during the next round of test, and provide feedback.     ... View more

Re: Wi-Fi clients not obtaning DHCP Address

by in Wireless
‎Aug 9 2019 1:16 PM
‎Aug 9 2019 1:16 PM
Now running 26.4 on all APs.   Still have to the same issue.   DHCP Failures from the LAN tab for the AP that the test device is connecting to.   DHCP request status on VLAN 3 5 of the last 5 requests did not receive responses.   Req. ID Client MAC Server IP Req. IP Req. type Resp. type Resp. IP RTT(ms) Ago(  247527957 fc:18:3c:61:a2:91 – – Discover – – – 26 247527957 fc:18:3c:61:a2:91 – – Discover – – – 24 247527957 fc:18:3c:61:a2:91 – – Discover – – – 20 247527957 fc:18:3c:61:a2:91 – – Discover – – – 11 247527957 fc:18:3c:61:a2:91 – – Discover – – – 2   You were correct on the AP TAG statement, that was for the VLAN Tagging in SSID configuration, not the VLAN setup for the APs. Thanks for clearing that up.   Dan     ... View more

Wi-Fi clients not obtaning DHCP Address

by in Wireless
‎Aug 9 2019 12:22 PM
‎Aug 9 2019 12:22 PM
Issue is that none of the Wi-Fi clients receive an answer to their DHCP request (Windows 10, Apple iOS, and Apple MacOS Tested). The MR45 devices are DHCP themselves do receive an IP from the same DHCP Server, in the same VLAN.   Access Points: MR45 Firmware: MR 25.13 Switch: Cisco C2960XR Ver: 15.2(2)E4   SSID in Bridge mode, with VLAN Tagging. AP Tags for APs, setting VLAN ID to 3   Cisco port config: interface     switchport trunk native vlan 3     switchport mode trunk     srr-queue bandwidth share 1 30 35 5     priority-queue out     mls qos trust dscp     auto qos trust interface Vlan3     ip address ###.###.3.254 255.255.255.0     ip helper-address ###.###.1.15   DHCP Server is Windows Server 2008 R2, no errors logged in the event log from the DHCP-Server. 60% of the IP addresses in range of DHCP Scope are available.   Wi-Fi clients joining the same VLAN from Cisco AP devices do not have the same issue.   Side note: I have a different SSID for a guest network, on the same Meraki APs set at Bridge Mode as well, but the DHCP request are handled local to the VLAN. This is working with no issues.   ... View more
© 2024 Cisco Systems, Inc.