Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
- About dsekely_brs
About dsekely_brs
dsekely_brs
Comes here often
Member since Aug 8, 2019
Dec 28 2023
Community Record
22
Posts
0
Kudos
0
Solutions
Badges
Oct 2 2023
7:27 AM
@RaphaelL that looks like what I need. When I run it for my networks the totals don't match up example in the dashboard for the past 7 days it shows 565.4MB for this one AP but this is what I get from the API [{'startTs': '2023-09-25T00:00:00Z', 'endTs': '2023-09-26T00:00:00Z', 'totalKbps': None, 'sentKbps': None, 'receivedKbps': None}, {'startTs': '2023-09-26T00:00:00Z', 'endTs': '2023-09-27T00:00:00Z', 'totalKbps': None, 'sentKbps': None, 'receivedKbps': None}, {'startTs': '2023-09-27T00:00:00Z', 'endTs': '2023-09-28T00:00:00Z', 'totalKbps': None, 'sentKbps': None, 'receivedKbps': None}, {'startTs': '2023-09-28T00:00:00Z', 'endTs': '2023-09-29T00:00:00Z', 'totalKbps': None, 'sentKbps': None, 'receivedKbps': None}, {'startTs': '2023-09-29T00:00:00Z', 'endTs': '2023-09-30T00:00:00Z', 'totalKbps': 5, 'sentKbps': 0, 'receivedKbps': 5}, {'startTs': '2023-09-30T00:00:00Z', 'endTs': '2023-10-01T00:00:00Z', 'totalKbps': 26, 'sentKbps': 6, 'receivedKbps': 20}, {'startTs': '2023-10-01T00:00:00Z', 'endTs': '2023-10-02T00:00:00Z', 'totalKbps': 19, 'sentKbps': 2, 'receivedKbps': 17}]
... View more
Oct 2 2023
5:54 AM
Is it possible to pull the usage information for MR AP's using the API? I've tried some of the usage I want to setup an email alert if an AP does not have usage in the past x days/hours. I have had issues with some AP's and they need to be rebooted. This information is on the web GUI as seen below
... View more
Sep 29 2023
3:18 PM
Has anyone had issues with clients not connecting to MR66's? I have a couple that the AP is on the network, broadcasting a signal on both bands but no clients will connect. If I reboot the AP the clients connect and the AP will work as expected. This happens randomly and I have not been able to find anything that might cause it and it is causing productivity issues as scanners/mobile printers start to lag and things take longer to process. Users have to walk to a different area for their devices to work normally. firmware version MR 26.8.3
... View more
Labels:
- Labels:
-
Other
Sep 9 2019
9:23 AM
@WldWzl Did you experience similar issues as me before the MTU change? I tested this unit again on different network within our organization and the results were the same. I was testing with two users trying to do speed tests and it was timing out and pages taking a while to load
... View more
Sep 6 2019
9:41 AM
@Happiman With the Cradlepoint I avg 15Mbps D and 8Mbps U Did you see my response regarding setting the Cradlepoint as a DHCP server instead of Pass through to my Meraki MX?
... View more
Sep 4 2019
12:15 PM
@Happiman Isn't that the same as using LAN1 instead of LAN2? If so I tried that as well.
... View more
Sep 4 2019
11:40 AM
@cmr I have not tried the 15.x firmware with the cradlepoint. I did however try it when I was troubleshooting a USB modem prior to getting the cradlepoint. The 15.x firmware did not help with the USB modem
... View more
Sep 4 2019
11:38 AM
@Happiman The Meraki WAN interface is set for DHCP and I'm using the dynamic IP from verizon connected to the pass-through LAN2 port on the CradlePoint.
... View more
Sep 4 2019
8:17 AM
I also tried turning off IDS and AMP and didn't see any change. I don't expect this connection to be as fast and stable as cable/fiber but I was honestly expecting more than what I an experiencing.
... View more
Sep 4 2019
8:12 AM
Having support change the MTU to 1428 which is what the cradlepoint is set to did not make any difference. Any other suggestions or information that would assist in troubleshooting?
... View more
Sep 3 2019
8:40 AM
I haven't looked on the Meraki side. I have made sure the cradle point was using the specified 1428 MTU
... View more
Sep 3 2019
7:30 AM
MX firmware is 14.40 We do have some of those features enabled but I was also able to mirror our production setup on a test MX84 and with just my laptop connected things were fine. I seem to have the issues when I add more devices behind the MX84 if that makes sense.
... View more
Sep 3 2019
6:43 AM
Need some assistance from the users that have successfully setup a cradle point as a cellular backup device for an MX84. Here is what I am experiencing. When connected to the cba850 directly from my laptop the cellular connection is smooth, speeds and signal strength are also good. When I connect the cba850 to a WAN port on the MX84 and access the internet through the MX I get spotty connection. Sometimes it is good and I can run speed tests and browse sites and other times sites time out as well as speed tests. When I am able to run speed tests they line up with the speed I was seeing while directly connected to the cba850. I had similar issues when using the USB modems connected to the MX84 but was never able to successfully browse websites so I am moving in the right direction. We are using verizon without static IP and using the LAN2 port for IP Pass through. Any help/suggestions would be appreciated.
... View more
Aug 19 2019
9:17 AM
@PhilipDAth Another user replied to the post below with a similar issue I am having. I however did not have any flow preferences on any of my networks that I am experiencing this issue. I'm just wondering if there is a setting with the S2S VPN that could be causing my issue as well. https://community.meraki.com/t5/Security-SD-WAN/Cellular-and-VPN-in-MX/m-p/4836
... View more
Aug 16 2019
4:19 PM
Nslookups completed as well. I was using internal dns servers behind the mx as well as using google dns servers when I was directly connected to one of the mx lan ports.
... View more
Aug 16 2019
2:11 PM
I am experiencing these issues when testing our cellular failover on a MX84 with a UML290 and USB730L. Both cellular devices work perfectly when connected to a laptop and are setup to connect automatically. When plugged into the MX84 they both are in the ready state and when I disconnect primary WAN the MX84 does fail over to cellular modem but I am not able to browse to any new websites. The pages just time out. If I happen to have websites open prior to the failover I am able to browse through the sub pages but any links to pages outside of that site time out as well. While on cellular failover I can ping and trace route to any website from my workstation. I am also able to get emails and instant messages to come through. I was able to test the device in another MX84 that I replicated as much as possible the configuration from the MX having the issue above and the device worked without any issues. What settings would be a good starting point to review given the non working behavior above?
... View more
© 2024 Cisco Systems, Inc.
