Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Register or Sign in
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
About HectorLaya
Community Record
11
Posts
2
Kudos
0
Solutions
Badges
Dec 10 2019
8:40 PM
1 Kudo
I think it would be great if you can have the option to upload AP configuration (name, ip address etc) from a batch file. Sometimes you have to change parameters of APs in large network and can be a little time consuming.
... View more
Nov 12 2019
8:22 AM
Nolan, Thank you very much for your feedback. Will open a case and wait (hope) for a quick fix... This is a configuration that we use a lot and with hundreds of APs at a time... Have a good day Regards Hector Laya
... View more
Nov 12 2019
8:07 AM
Godd Morning, I'm having a weird behavior in the Meraki Dasboard configurint Manual channles and transmit power in radio settings. Previously, I could configure the channels manually and then the transmit power with the edit bulk options. But now, when I configure the second options, the first one came back to auto. For example, if I configure the channels manually in channel 6, it takes the config, but then when set the transmit power static to, let's say 14dBm, it configure the transmit power but then the channel came back to auto. And viceversa... I had done this before without problem, but now I can't. The work around that I found was entering in the old version of the Radio Settings page and change the parameters one AP at time... Thanks in advance for your attention Regards Hector Laya
... View more
Jul 12 2019
9:12 AM
Thanks to all for your attention. The cables used are the correct. The issue was that the stacking ports were disabled through the APIs. Stack ports enabled and working fine. Regards
... View more
Jul 11 2019
8:58 AM
Thanks to all for your messages, I was out off sight for a while. The switches are running latest firmware MS 11.22 There is no led on the Stack ports The stack port shows disabled even in other switch that has no stack cable attached All the switches are in the same organization in the Dashboard
... View more
Jun 17 2019
9:57 AM
Thanks, The Switches are stacked physically: SW1 port 1 to SW2 port 2, SW2 port 1 to SW1 port 2
... View more
Jun 17 2019
9:13 AM
Good afternoon, I have 3 stacks of 2 x MS350-48FP each one but the stack ports shows as "Disable" in the Switch on the Dashboard. I tried reconnecting the stack cables and power cycle the switches but didn't work. In the dashboard there is no option to enable the stack ports. Also, in the Switch Stacks configuration area on the dashboard it shows that there are no potential stacks detected. What can I do to solve this issue? Thanks in advance for your attention Regards
... View more
Jun 16 2019
1:35 PM
1 Kudo
Thanks to all for your attention. It was a Bad AP. I changed the AP and port went up without issues. But Meraki should be aware of this icon and put the information in the documents... Thanks again.
... View more
Jun 12 2019
9:26 AM
Thank to all of you for your attention and time to reply me. I thought about the bad pair for tx/rx but the cable test shows ok in all pairs. Firmware is updated. Also, had tried recycling the power of the port, resetting the switch, etc. It seems a bug, but i'm not really sure. Will continue researching and trying and will post the results. Regards
... View more
Jun 12 2019
12:05 AM
There is an MR30H AP connected to that port (16). Also, have other switch with the same icon. AP is not coming online, is like nothing is connected. I did a cable test and all pairs show Ok. I see a 2.1 W on power usage. Weird that I couldn't find any documentation from Meraki with that icon...
... View more
Jun 11 2019
11:36 PM
Good evening, I have some switch ports showed in black with a green lightning bolt in the sumarry tab when I'm in the Switch page. I searched the Meraki documentation but only make reference to a black port. Nothing about the icon that I have (ref port 16 in image attached). Thanks in advance for your attention.
... View more
My Top Kudoed Posts
| Subject | Kudos | Views |
|---|---|---|
| 1 | 26867 | |
| 1 | 10811 |
© 2024 Cisco Systems, Inc.
