Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Register or Sign in
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
About nikma
Community Record
10
Posts
2
Kudos
0
Solutions
Badges
Jul 3 2019
4:38 AM
Hi guys, When I try to do packet capture on the security appliances on the lan interface for capturing broadcast packets, I dont see any dhcp discovery packet from the client toward the firewall. But on the event log I do get lots of event type of DHCP problem: Jul 3 13:33:34 workstation-test DHCP problem extra: no_offers_received, vap: 0, vlan: 20 Do you guys think that it should be sufficient with those three configured steps on the firewall: 1. There is site to site vpn rule configured that permits all services from the client vlan into the server vlan on the other side (behind the MX firewall) 2. The relay server which is going to be used from the client vlan is also specified, and 3. Vpn route that routes traffic from the client network to the server network (behind the MX) is also configured. Best regars,
... View more
Jun 24 2019
2:50 AM
1 Kudo
Hi Jdsilva, Thank you for these information. They are indeed very useful! BR Nikma
... View more
Jun 20 2019
3:12 AM
Hi, We need to open ntp port 123 from one vlan to another. I have created a rule that allows ntp from that vlan 10.10.10.0/24 to the another 10.10.20.0/24 on udp port 123. But it is still not working! Source - 10.10.10.0/24 Destination - 10.10.20.0/24 Src port: any Dst port: 123 Should I open on the other side also! Is there a need for that? BR Nikma
... View more
Jun 18 2019
12:31 AM
The DHCP server is located on another site and it is working for some other sites. The problem is only with one site!
... View more
Jun 18 2019
12:31 AM
Hi PhilipDAth, Seems that the MS switch has all the half of the ports tagged on vlan 60 and the other ports are trunks (native vlan 1, allow all other vlans). The vlan which the clients should sit and get IP address is vlan 20 but this vlan is not present on any of the ports on the switch. I will try to solve this issue and concentrate on this point then I will have you know how it went!
... View more
Jun 17 2019
6:36 AM
Hi, We are experiencing a DHCP issue with one of our vlans. Clients on our separated vlan aren't getting any IP via meraki. The DHCP server resides on another subnet and we have activate the relay server on the DHCP on the meraki dashboard. The policys are all right and verified that they allow traffic in and out the network which the dhcp server resides. How can this problem be solved, is there any recommandation to follow or any tools embedded on dashboard that can be used? Another question! Is ipv6 pools supported through meraki firewalls, and does IGMP snooping affect in any way ipv4 or ipv6 leasing for clients? Thanks in advance!
... View more
May 26 2019
11:25 PM
1 Kudo
All right Philip! We will investigate further regarding the MFA solution but as for now we have decided to use Azure MFA! What do you think about the configuration on the meraki itself! Do we have anything else to do beside these points down: 1. We enable Client VPN on the meraki dashboard, 2. We choose an IP range under Client VPN Subnet (does this mean that this is the range that the client will be assigned IP addresses from?), 3. We specify then the dns server which will be used, t 4. We specify the secret and the authentication method which in our case will be Radius! The radius server will be a NPS server and the Azure MFA extension will be installed on this server! And in the end we probably should create a policy to accept this kind of traffic inside the coorporate network!
... View more
May 24 2019
2:13 AM
Hi, Thank you Philip for your response! So we enable Client VPN on the meraki dashboard, we choose an IP range under Client VPN Subnet (does this mean that this is the range that the client will be assigned IP addresses from?). We specify then the dns server which will be used, the secret and the authentication method which in our case will be Radius! The radius server will be a NPS server and the Azure MFA extension will be installed on this server! Do I have a good framework from which to start? BR Nikma
... View more
May 24 2019
1:53 AM
Hi, I am very new to meraki and I dont have experience with these products but I hope I am on the right place to get some help. We need to implement VPN client for our users with meraki firewalls and implement also 2FA with azure. We have this competence to do this, but we are lacking on the meraki competence. Is there anyone who can guide me to achieve this? BR Nikma
... View more
My Top Kudoed Posts
| Subject | Kudos | Views |
|---|---|---|
| 1 | 3216 | |
| 1 | 30908 |
© 2024 Cisco Systems, Inc.
