Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
About TownofMidland
TownofMidland
Here to help
Member since May 17, 2019
Oct 30 2019
Community Record
7
Posts
0
Kudos
2
Solutions
Badges
Oct 16 2019
7:07 AM
I think I may have it. The key issues appeared to be time & Native VLAN In regards to TIME - I have run into this before with Meraki devices and I can only guess that being a cloud based config, sometimes they need time to settle into their configuration. My experience has shown that some devices like the MX and apparently those in this type of configuration, are more sensitive to constant changes As for Native VLAN – I reset everything to the default VLAN of 1 then once everything settled in (alerting but still working) I changed things around to my desired configuration So what did I do? Set up the Gateway and Repeater APs and left it working with nothing connected and no changes over the Thanksgiving long weekend Took the remote switch and reset it to factory settings (no configuration) Plugged it in and left it for 30 min. Everything stayed ONLINE though the remote switch was alerting (management address from wrong VLAN) Then I started configuring the Native VLAN for management (on the TRUNK uplink port) along with the same VLAN for the remote wired devices (on the Access ports) Set a static management IP Wired clients getting DHCP addresses (on the native VLAN) Wireless getting DHCP addresses per SSID
... View more
Oct 11 2019
11:47 AM
Yup, just wired and unfortunately no, I do not have another switch to use. Now to add to my joy, the repeater isn't coming back online. With a long weekend coming, the pub is looking real good right now.
... View more
Oct 11 2019
10:42 AM
Thank you. That covers one concern that the single ethernet jack MR74's (as opposed to the two-port MR84's) could not handle this type of set up The bridge SSID is set to Bridge Mode and the clients are that are wired are set globally to behave like they are connected to the SSID. When I had my remote switch set to trunk - at least the repeater came back online after unplugging the switch. In access mode or with the dumb switch, it needs a reset to come back to life. Right now, line of sight is awesome. They are on either side of our config room (but up high so no sterilization is happening). I am wondering if it is the MS120-8 giving the issue? I just need to run security cameras and some building automation and it will be a 'not so great' environment (it is a cold storage shed for maintenance equipment) so I went with a lower model instead of my usual MS250's. I am still digging.
... View more
Oct 11 2019
10:05 AM
I have been trying to set up a simple wireless connection to an outlying building and have been unsuccessful. I am using two MR74s and they set themselves up as gateway and repeater just fine. Things go south whenever I plug a switch into the repeater. No matter what I plug in, a Meraki switch or a cheap, dumb switch; the repeater goes offline and I have to disconnect the switch and perform the (not so factory) factory reset on the repeater to get it to connect again. I have tried various combinations of the uplink port on the repeater switch being TRUNK, ACCESS, one or more VLANs - whatever (the documentation never actually states how it should be set) to no avail. I have manually chosen the radio channels so they always find each other I have set the VLAN on and off the BRIDGED SSID I have only configured one VLAN across the link Every time I plug something into the power injector of the MR74, things stop working. Does anyone have any suggestions? In particular, I wish to confirm: The GATEWAY AP - it's uplink switch port should still be TRUNK? Does VLAN tagging on the SSID Access Control have any effect?
... View more
May 30 2019
10:55 AM
Lots of trial and error indicates that if I set the Block Encrypted Search option, all GOOGLE web pages in general are blocked. No other search engine is affected.
... View more
May 30 2019
10:16 AM
Exhaustive testing has shown that it is the Meraki device blocking GOOGLE web pages somehow. Name resolution is fine, it is just GOOGLE web pages that are blocked. Support claims the configuration is OK but I am going to try a wipe and reload.
... View more
May 17 2019
8:20 AM
I have a weird one. We have a number of MX's providing our Wi-Fi via MR33's. We recently purchased an MX67W and have encountered the following puzzling issue: Wi-Fi connectivity is fine and internet access is completely functional When our mobile devices (Android, we have no iPhones) connect to to the MR33 AP's, everything is complete, 100% flawless Yet, when we connect to the MX67W wireless, the phones display the error message 'internet may not be available' yet, internet access is completely fine! Despite the message, I turn off the cell radio and can browse the internet, run speed tests, whatsmyip shows the correct answer. So, internet access is working fine! I have removed all geofiltering, I use GOOGLE DNS instead of our DNS filtering, I go back to factory settings and still the message appears, yet everything works. I have stumped Merki support. I have done lots of GOOGLEing to no avail. While this is not a show stopper it is an irritant to the end users.
... View more
My Accepted Solutions
| Subject | Views | Posted |
|---|---|---|
| 4292 | Oct 16 2019 7:07 AM | |
| 2620 | May 30 2019 10:55 AM |
© 2024 Cisco Systems, Inc.
