- About ehsan230564
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
ehsan230564
Comes here often
Member since May 15, 2019
09-26-2019
Community Record
16
Posts
0
Kudos
0
Solutions
Badges
09-26-2019
06:42 AM
Dear Sir, While connecting from windows l2tp client vpn to MX64, getting error as :- ERROR 789 l2tp connection attempt failed.
... View more
09-26-2019
12:23 AM
Dear Sir, My MX64 is it sitting behind another device doing NAT. And I configured the MX WAN IP as DMZ in Internet router. Also I tried to connect with Android built in VPN client, and the error is : unsuccessfull Thanks and regards.
... View more
09-23-2019
11:57 PM
Dear Sir, Can we configure both site to site VPN as well as enable client VPN sever in a single MX64 device. Thanks and regards.
... View more
09-22-2019
05:01 AM
Dear sir, When I trying to connect the cilent vpn server for mx64, android built in vpn client giving error as :- unsuccessful. Also when I trying to connect with Cisco Any connect for android client than it is giving error as :- your host name is unreachable. Although my MX64 is showing online. Also I am trying to ping the MX64 full host name from outside using internet it is giving error as :- request time out. In my internet router I did forwarded port UDP 500 and UDP 4500 to the MX64 IP. So it is look like outside world are not able to resolve the MX64 full host name. Thanks and regards.
... View more
09-22-2019
12:56 AM
Dear Sir, I cannot reach dynamic host name for my device mx64. My wan port ping is enable. Thanks and regards
... View more
09-19-2019
08:07 AM
Dear Sir, I did client vpn server setting for mx4 and i trying to connect using android vpn client, it is giving unseccesfull. Thanks and regards.
... View more
09-15-2019
05:34 AM
Dear Sir, I did the port forwarding settings for both Meraki as well as Internet router also. But still I am getting VPN as NAT Type Unfriendly.
... View more
08-01-2019
01:24 AM
Dear Sir, After creating warm spare between two Meraki MX64, the SPARE is unreachable. Both the Meraki are connected to a switch by their lan1.
... View more
06-26-2019
04:19 AM
Hello sir, I have two windows server, 1st server ip = 192.168.0.1 default gateway 192.168.0.100 2nd server ip = 192.168.0.200 default gateway 192.168.0.100. Two MX64 in HUB site to site vpn, 1st MX64 HUB1, LAN ip = 192.168.0.100 2nd MX64 HUB2, LAN ip = 192.168.1.100. three MX64 in spoke site to site VPN with HUB1. another thhree MX64 in spoke site to site VPN with HUB2. But we want to access above mentioned both the server from all the spoke. since internet speed are less speed so we want to divide 3:3 branches(spoke). also if one HUB1 device get problem still at least three branches will be working through. If we connect all the 6 branches (spoke) to same HUB with two wan internet load balancing will be there, but id the device get fail than all the six branches will stop accessing the Head office. So my requirement is HA with load balancing and also fail over VPN. Thanks and regards.
... View more
06-26-2019
04:18 AM
Hello sir, I have two windows server, 1st server ip = 192.168.0.1 default gateway 192.168.0.100 2nd server ip = 192.168.0.200 default gateway 192.168.0.100. Two MX64 in HUB site to site vpn, 1st MX64 HUB1, LAN ip = 192.168.0.100 2nd MX64 HUB2, LAN ip = 192.168.1.100. three MX64 in spoke site to site VPN with HUB1. another thhree MX64 in spoke site to site VPN with HUB2. But we want to access above mentioned both the server from all the spoke. since internet speed are less speed so we want to divide 3:3 branches(spoke). also if one HUB1 device get problem still at least three branches will be working through. If we connect all the 6 branches (spoke) to same HUB with two wan internet load balancing will be there, but id the device get fail than all the six branches will stop accessing the Head office. So my requirement is HA with load balancing and also fail over VPN.
... View more
06-26-2019
03:56 AM
Dear Sir, How can I do VPN load balancing, I have two mx64 in hub mode, and three mx64 in spoke connecting to hub1 and another three mx64 to hub2. I want to access the same server with IP = 192.168.0.1 from all the 6 spoke in above scenario. Since it is not allowed configure the both the HUB in same subnet. so that I can connect both the HUB to the same switch in which server is connected.
... View more
06-26-2019
03:28 AM
Dear Sir, If Two Meraki mx64 are in HA warm spare. And both the device WAN1 are connected to different ISP internet. Is it possible to configure internet load balancing as well internet fail over between primary and spare WAN1. Thanks and regards.
... View more
06-26-2019
01:35 AM
Dear Sir, Is it possible for Two MX64 in same subnet with HUB VPN in same subnet aatched to same switch.
... View more
06-22-2019
07:48 AM
Dear Sir, My scenario is that I have two 4g internet connected to one device MX64 to wan1 and wan4, and configured as site to site HUB vpn, with Automatic NAT traversal. And another MX64 device with another 4g internet connected to wan1. And configured as site to site spoke VPN to the first HUB as specified above. I got the VPN established but I got message as NAT Type : Unfriendly. And I am not able to ping connected to the LAN port of MX64 configured as HUB VPN. Since I have all the WAN as AUTO DHCP. How should I configure :- Manually create a port mapping on the upstream firewall that will forward all traffic received on a specific public IP and port to the internal address of the appliance on the selected port. In Dashboard on the Security & SD-WAN > Configure > Site-to-site VPN page use the Manual: Port forwarding option for NAT traversal, and provide the public IP address and port that was configured. Thanks and regards.
... View more
05-15-2019
04:59 AM
How can I create site to site auto vpn between mx84 and mx64 but user can only access vpn and do not access internet.
... View more
