Meraki

Community
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Show  only  | Search instead for 
Did you mean: 

About AlexTauer

Re: Question regarding Layer 3 firewall setting and a remote connection

by in Security & SD-WAN
‎Aug 20 2018 2:47 PM
1 Kudo
‎Aug 20 2018 2:47 PM
1 Kudo
Thanks.  I figured that there was something else that I was missing.  I'll give that a shot. ... View more

Question regarding Layer 3 firewall setting and a remote connection

by in Security & SD-WAN
‎Aug 20 2018 2:39 PM
‎Aug 20 2018 2:39 PM
Hey guys and gals,   I did some browsing before deciding to post, as I couldn't find an answer that helped me any.   I have a camera security system, running on the network behind my firewall (MX84).  I can access the IP addy of the DVR from any PC that is connected to our internal network, without a problem.  I was recently tasked with getting the owner of this location remote access to the DVR.   Now, obviously I should be able to go into the MX device and add an inbound layer 3 rule that basically states to allow any external IP access to the IP and port # for the DVR.  I have done this, but I still cannot get to the login page for the DVR.  My DVR is configured to use port 82, and I believe that I have it configured properly (see attached).  I know that the xxxx should be an IP, but I don't wanna post it for security reasons.   Can anyone possibly show me where I have messed up (if I have messed up)?     ... View more

Re: MR74 Speed Issue

by in Wireless
‎Aug 6 2018 1:09 PM
‎Aug 6 2018 1:09 PM
Thanks for the suggestion!  I will try that as well.   ... View more

Re: MR74 Speed Issue

by in Wireless
‎Aug 6 2018 7:17 AM
1 Kudo
‎Aug 6 2018 7:17 AM
1 Kudo
I believe that Adam may have pinpointed the issue.   The AP is mounted on the front of our building, facing out towards a major interstate (I-45 in Houston).  Looking through logs and the air marshal reports, I am finding that it is being bombarded with other SSIDs, more than likely from passing vehicles (seeing names like Gary's Silverado, Sharon's iPhone, etc.).  I'm also picking up our signal on the opposite side of the interstate (don't need to go out that far).  I'm going to try dialing back the transmission power a tad bit, to where its just covering our designated area.  Its going to take a bit of trial and error, but I think I can get it brought back in range.   I did also try changing the broadcast channel to one that is not as congested, so we'll see how that helps as well.   Thanks for the input guys.  I'll post back in a few days with the results of my tests. ... View more

MR74 Speed Issue

by in Wireless
‎Aug 3 2018 10:07 AM
‎Aug 3 2018 10:07 AM
Hey guys and gals,   Encountering an issue with an MR74 that I have providing coverage for the parking lot at the dealership I work for.   Speeds through the WAP spike at 30-40 Mbps down before dropping to 3-5 Mbps.  Upload speeds spike at 20-25 down, and drop down to 4-5.  All other access points provide 250-300 Mbps down, and 30-50 up, which is what our provider is showing our account to be set to.  This WAP was working just fine a couple weeks ago.   I have rebooted the AP, performed a factory restore, have verified that there are no cabling issue, and have verified that there are no settings differences between this WAP and the two others I have on site that are working.  All WAPs are running back to the same Gigabit network switch, which has not encountered any issues.   Anyone have any ideas? A coworker is thinking that it may be a heat issue (WAP is mounted to the side of the building, and receives full sunlight for a good 8-10 hours a day).  I have not done any temperature readings on the device yet, but they are rated for up to 130*F and I don't think that its getting that hot (I could be wrong though). ... View more
© 2024 Cisco Systems, Inc.