Hi All,      I have MS Switches on 14.33.1    MAB access policy below    My requirement is to have a fail open " when there is an outage on ISE, the port need to set to open with no 802.1x"  that is why I have my critical auth vlan as the data vlan. in my case is vlan 2    My problem it has been for a long time now is that even though ISE is sending Radius accept "I see the logs on ISE " , Meraki port is getting put in guest vlan        ... View more

Hi All,      I'm getting OBJ(766174886606406852) as a result of the source IP address of a rule from the MX firewall. The source in the first place is an object from a security config template    The template has 100+ networks bound to it.    example  policy : allow , protocol Any source HR subnet "  Vlan 6 : 10.10.10.0/24" , destination 10.10.100.0/24    I notices some sources not all of them getting OBJ(766174886606406852)    other sources are retrieving the Vlan only not the subnet with it  is there is a way i can have the name of the object " HR subnet" and the vlan with the subnet in the result?    Thank you!  ... View more

  HI All,      Trying to loop over every firewall rule in my org and I'm getting the error blelow.      response = dashboard.organizations.getOrganizationNetworks(org_id)   for network in response:         fw_rules =  dashboard.appliance.getNetworkApplianceFirewallL3FirewallRules(network['id'])   File "C:\Users\p00091670\AppData\Local\Programs\Python\Python310\lib\site-packages\meraki\rest_session.py", line 277, in request raise APIError(metadata, response) meraki.exceptions.APIError: appliance, getNetworkApplianceFirewallL3FirewallRules - 404 Not Found, please wait a minute if the key or org was just newly created.     My debug file showing below    2022-07-16 19:22:43       meraki:    DEBUG > {'tags': ['appliance', 'configure', 'firewall', 'l3FirewallRules'], 'operation': 'getNetworkApplianceFirewallL3FirewallRules', 'method': 'GET', 'url': '/networks/XXXXXXXXXXX/appliance/firewall/l3FirewallRules', 'params': None} 2022-07-16 19:22:43       meraki:     INFO > GET https://api.meraki.com/api/v1/networks/XXXXXXXXXXXXX/appliance/firewall/l3FirewallRules 2022-07-16 19:22:43       meraki:    ERROR > appliance, getNetworkApplianceFirewallL3FirewallRules - 404 Not Found, b''    Any idea, please?    ... View more

Hi All,     can we do wake on LAN with 802.1x in Meraki? if not is there any way we can use API to invoke hosts to start communicating with the ports?      ... View more

Hi All,      we have Merkai MR access points that are going into a repeater mode and causing loops in the network. these access points are power with a power injectors " not a POE from the switch " , when we upgrade the switches and reboot. MR will lose access to the gateway but it still powers up from the power injector then it goes into repeater mode.    any way I can stop it from going into repeater mode?  ... View more

Hi All,      Trying to get MX traffic analysis history. so I need to get things like the total of MS teams usage for a month, using the below API?    {{baseUrl}}/networks/:networkId/traffic   I'm getting error  timespan is too large if I don't send time spam and send t0 only. I need the traffic for a month, so if I set t0 for today do I need to pass another parameter t1 for the range of a month ?        ... View more

Is there is anyway i can find the bridge ID of the switch that is generating the STP changes can I see something in the logs maybe?  ... View more

Hi,      is there a supported design where all guest traffic can go to a centralized " controller" in the data center then from there they can get to the internet? I'm trying to have all of my guest users use one NAT IP address only from all remote sites. the current design is all guests are using the same IP address that the site uses to access the internet.    Thank you   ... View more

HI ALl,      Is there an API that will list the endpoint's IP address for the clinets that are connected to a switch?    ... View more