Meraki

redsector · ‎Apr 5 2022

took the transition mode, so can clients which are not able for WPA3 use WPA2

redsector · ‎Apr 5 2022

yes, no PoE shown and the "Power" Menue doesn´t work.

redsector · ‎Apr 3 2022

Take the newest firmware version: MR28.6. It solved a lot of issues in my network.

redsector · ‎Mar 25 2022

staggered with offset

redsector · ‎Mar 25 2022

About 1000qm (square meters) on two floors for "pick by voice" devices.

redsector · ‎Mar 23 2022

Seems to be good now, no issue since an hour.

redsector · ‎Mar 23 2022

It was marked as solved, but it isn´t. Problems still occure.

redsector · ‎Mar 23 2022

Still a few AP´s not reachable

redsector · ‎Mar 23 2022

The devices are working well, only the dashboard connection is affected. Users don´t see any trouble.

redsector · ‎Mar 23 2022

Use a paperclip and push the reset button for about 15 seconds.

redsector · ‎Mar 23 2022

Same Problem here all MR36, MR46, MR46E, MR55 are affected saying "no connectivity". But all MR42, MR42E, MR33, MR32, MR18 are not affected, also all switches are not affected.

redsector · ‎Mar 23 2022

Same Problem here all MR36, MR46, MR46E, MR55 are affected saying "no connectivity". But all MR42, MR42E, MR33, MR32, MR18 are not affected, also all switches are not affected.

redsector · ‎Mar 22 2022

Newest firmware in use? Use MS14.33.

redsector · ‎Mar 22 2022

PVST was nice when the trunk connections weren´t strong enough for one line and then to be shared on more lines with PVST. But nowadays fibre cables running with 10G or aggregated more faster I don´t see any reasons to have PVST. In fact: It´s more difficult to find an network error with PVST/PVST+.

redsector · ‎Mar 22 2022

We have got MR32 too, they are running well with firmware MR26.8.3 The only thing is: the LED light is fading out by time.

redsector · ‎Mar 22 2022

We have got in every second line an accesspoint in our warehouses. where not then alternately, on the opposite site. And with patch antennas facing in the shelfe alleys. Running with 12MBit minimum. Autopower. Mixed 2.4GHz and 5GHz. Each line is about 60m (about 200ft) long.

redsector · ‎Mar 15 2022

MR28.6 on the accesspoints?

redsector · ‎Mar 14 2022

the logs are clean

redsector · ‎Mar 14 2022

o.k. I will try. but this could last a while. I will keep you informed. Thank you

redsector · ‎Mar 14 2022

thank you. show spanning-tree vlan 3: Po6 Desg FWD 10000 128.2382 P2p interface Port-channel6 description Uplink to Meraki-Switch switchport mode trunk spanning-tree guard loop end

redsector · ‎Mar 14 2022

Hello, I have got a strange issue with trunk-ports from Cisco classic WS-C3850-12S to Meraki MS120-48LP. Some VLANs don´t get trough the trunk line. The MS-switches are on Firmware MS14.33 and the Cisco Classic switches are on the newest recommended software version. The trunk ports are not restricted in any way (all VLANs allowed). VLAN 3 is not possible to get trough, VLAN1,2,5,8 are going trough. I tried it with port aggregation/etherchannel but also without. Spanning-tree works good. Standard VLAN is VLAN1. devices in VLAN3 can´t see each other on the other side but each device can see devices in this VLAN on the own switch. Other VLANs are working well, and all devices can see each other independent on which switches. Is that an bug? Or am I stupid?

redsector · ‎Feb 25 2022

We have got many Avaya SIP PoE phones connected to MS225 switches (firmware version MS14.32 and MS14.33) SIP phones are connected to ports configured with voice-VLAN and client-VLAN, clients are connected to the SIP-phone. No issues like that. only issue is that the phones sometimes reduce speed from 1Gig to 100MBit without any reason.

redsector · ‎Feb 25 2022

it was the power saving mode causing the erroros. I did switch off any power-saving modes, since then no CRC-errors occured.

redsector · ‎Feb 25 2022

Thank you. i will keep an eye on it.

redsector · ‎Feb 24 2022

Hello, I need to equip an 3 floor office building, replacing old Cisco classic controller based accesspoints, with new Meraki MR accesspoints (about 15 devices). Because I don´t want to install "old" hardware (it should keep for 10 years) but also not new hardware with many bugs... I am thinking to install the new MR57 to be safe for future requirements. The question is: is there any expericence with that WiFi 6E standard? bugs in the MR software? Is it running smooth with existing (not WiFi 6E) devices, roaming? or future hardware obstacles? thank you

About redsector

redsector

Markus Moses

Community Record

Badges