MS410~Catalsyt9300間のリンクが上がらない

HCNET河合
Comes here often

MS410~Catalsyt9300間のリンクが上がらない

MS410-32~Catalst9300-24S-M間において1G光ケーブルを接続してもリンクアップしない。
原因について分かれば教えてほしい。

・MS410-32~Catalst9300-24S-M間はLAG接続
・光ケーブル自体は問題無し。
・Catalsyt9300~MS130間であれば問題無くリンクアップする。だから機器障害やSFP故障は無し。
・SFPはそれぞれMA-SFP-1GB-SXを使用している。

13 Replies 13
alemabrahao
Kind of a big deal
Kind of a big deal

Are you running the latest firmware version? Does the connection only work when LACP is configured? Have you tested on a Trunk port without LACP configured?

I am not a Cisco Meraki employee. My suggestions are based on documentation of Meraki best practices and day-to-day experience.

Please, if this post was useful, leave your kudos and mark it as solved.
HCNET河合
Comes here often

最新のファームを適用しています。
MS410:MS17.2.1
Catalsyt9300:CS17.2.1

Catalsyt9300はMerakiOSで動作させていますので、明示的にLACPの設定はしていないです。
MerakiOSでLACPの設定は可能なのでしょうか。

alemabrahao
Kind of a big deal
Kind of a big deal

I suggest you downgrade to 16.9 and retest. I have seen other people reporting issues with 17.2.1.

 

https://documentation.meraki.com/General_Administration/Tools_and_Troubleshooting/Link_Aggregation_a...

 

 

I also suggest you open a support case.

I am not a Cisco Meraki employee. My suggestions are based on documentation of Meraki best practices and day-to-day experience.

Please, if this post was useful, leave your kudos and mark it as solved.
HCNET河合
Comes here often

ダウングレードとはMS410 Cat9300どちらを指していますか。
17.2.1では具体的にどういった問題でしたか?

 

既にサポートには問い合わせ済みですが、調査中としか回答が来ていない状況です。

alemabrahao
Kind of a big deal
Kind of a big deal

For both.

I am not a Cisco Meraki employee. My suggestions are based on documentation of Meraki best practices and day-to-day experience.

Please, if this post was useful, leave your kudos and mark it as solved.
PhilipDAth
Kind of a big deal
Kind of a big deal

If running 17.2.1 you need to delete and re-create the LACP port-channels.

 

PhilipDAth_0-1747196441907.png

 

 

HCNET河合
Comes here often

MS410/Cat9300ともにMerakiなのですが、LACPポートチャネルはどうやって削除すれば良いのでしょうか。

 

alemabrahao
Kind of a big deal
Kind of a big deal

Splitting Aggregated ports

To split an aggregated link, simply select the aggregated port and choose Split. This will revert the changes and split the group into its own separate ports.

*For more specific configuration and interoperability information, please reference our documentation.

 

https://documentation.meraki.com/MS/Port_and_VLAN_Configuration/Switch_Ports#Splitting_Aggregated_po...

I am not a Cisco Meraki employee. My suggestions are based on documentation of Meraki best practices and day-to-day experience.

Please, if this post was useful, leave your kudos and mark it as solved.
HCNET河合
Comes here often

ありがとうございます。
>17.2.1を実行している場合は、LACPポートチャネルを削除して再作成する必要があります。
→これは17.2.1のBugですか?

HCNET河合
Comes here often

issureを見ると、[IF THE CONNECTED DEVICE NOT CONFIGURE FOR LACP]となっておりあくまでLACPに対応していない場合となっています。MS410/Cat9300ともにLACP対応機種かと思いますが、LAGポート削除→再作成が効果ありますか?

 

alemabrahao
Kind of a big deal
Kind of a big deal

Yes, that is the recommendation, if in doubt I suggest you open a support case.

I am not a Cisco Meraki employee. My suggestions are based on documentation of Meraki best practices and day-to-day experience.

Please, if this post was useful, leave your kudos and mark it as solved.
HCNET河合
Comes here often

並行してサポートに問い合わせたところ以下の回答でした。

> LAG関連の設定/接続方法を見直すことで改善する可能性はございますか。
LAG 構成ではない通常の 1 対 1 の接続でも発生している事象のため、上記で改善する可能性は低いと存じます。

 

LAGの組み直しで直った実績はありますでしょうか。

alemabrahao
Kind of a big deal
Kind of a big deal

Yes, probably.

I am not a Cisco Meraki employee. My suggestions are based on documentation of Meraki best practices and day-to-day experience.

Please, if this post was useful, leave your kudos and mark it as solved.
Get notified when there are additional replies to this discussion.