Change: New article.
Change: New articles regarding MX18.2.
Catalyst Meraki 9300 (C9300-M) datasheet
Change: New article.
Change: New article.
Change: New article.
MT15 Installation Guide - Indoor Air Quality w/CO2
MT15 Datasheet - Indoor Air Quality w/CO2
Change: New articles.
Change: New article.
Cisco+ Secure Connect - Manage DNS Policies
Change: Added section "DNS Design".
Getting started: Cisco Catalyst 9300 with Meraki Dashboard
Change: Added note that migration for C9300X-12Y, C9300X-24Y, C9300-24S and C9300-48S is currently in Early Preview and requires the switch to be on a special IOS-XE release (cat9k_iosxe.17.09.03m2.SPA.bin), in INSTALL mode.
FAQs: Migrate to Meraki management mode
Change: Added specific Fiber models and C9300-NM / C9300X-NM network modules to list of supported devices.
Meraki Subscription Licensing - Subscription Claim
Change: Added additional step 6 to "Claiming An Additional Subscription" to bind the networks to the newly added subscription. If you do not bind your networks, they will remain unbound and this can result in non-compliance.
Passthrough Mode on the MX Security Appliance and Z-series Teleworker Gateway
Change: Added note that vMX does not support Advanced Security and Secure SD-WAN Plus features as vMX licensing is limited to Enterprise licensing.
MX Warm Spare - High-Availability Pair
Change: Added note that the virtual uplink MAC of MXs in HA-pair (always starting with "cc:03:d9") is structured differently than the virtual MAC of MS switches acting in warm spare. For the MS switches, virtual MAC will always begin with with "88:15:44".
Change: Added section "Tunnel Recovery".
SD-WAN Internet Policies (SD-Internet)
Change: Added note about UI changes dependent of license type in use.
Security and SD-WAN (MX,Z) Features Directory
Change: Added MX 18.2.X Firmware Features.
Adaptive Policy for MX/Z Platforms
Change: Added changes regarding MX 18.2 enhancements; added sections "Static VLAN Assignment", "Static LAN Port Assignment" and "Enable SGT Peer on WAN interface (Concentrator Only)".
AnyConnect Client Download and Deployment
Change: Added note that Start Before Logon (SBL) is currently not supported with SAML Authentication.
Network Objects Configuration Guide
Change: Added "View Network Objects via API" to "Administration" table.
Change: Added section "Root Bridge Priority".
MS120 Overview and Specifications
MS250 Overview and Specifications
MS225 Overview and Specifications
MS350 Overview and Specifications
MS125 Overview and Specifications
Change: Clarified Power Load information.
Change: Added note that the key/value pair "udn:private-group-id" is case sensitive.
Change: Added MR36H.
MA-MNT-ANT-1 Installation Guide
MA-MNT-ANT-2 Installation Guide
Change: Added length of the mounting arms.
Change: Added warning that the MV93 and MV63 bodies can reach high temperatures during operation and should be handled with care.
Change: Added note that 2nd generation cameras will be upgraded from Zones to Areas starting October 17, 2023, to be able to use Line Crossing and Area occupancy.
Meraki Vision Portal Changelog
Change: Added release notes for up to v1.13.0.
Change: Added sensor metrics for MT11, MT14 (both Standard Operating Mode and High Sampling Mode), MT30 and MT40.
Change: Added question "What is a good signal strength for MT devices?".
Change: Added section "CO2 (ppm)".
Creating a Public/Private Certificate Pair
Change: Added note to convert the .crt file into a .der file, for use with FileVault Recovery Key Escrow payloads, as MacOS devices will reject .crt files.
Using the Organization Inventory
Change: Added section "Bulk Switch Replacement".
Using the Cisco Meraki Device Local Status Page
Change: Added section "IPv6 Support on MX Security & SD-WAN Platforms".
Meraki Per-Device Licensing Overview
Change: Added note to queue licenses before the 90-day pre-activation period expires, to avoid the state "Active and unassociated (unused active)".
