Documentation Digest: March 8th - March 15th

Hannah-C
Meraki Employee
Meraki Employee

Documentation Digest: March 8th - March 15th

DocDigest_Banner.png

 

New Articles:

Meraki Subscription Changes

Change: New article.

 

Secure Connect: Site Localization

Change: New article.

 

Systems Manager Agent Upgrade 2024

Change: New article.

 

Basic SFP Troubleshooting Guide

Change: New article.

 

Traffic Analysis and Classification

Change: New article.

 

Secure Connect:

Cisco Secure Connect - Manage Web Policies

Change: Added "At this time QUIC protocol is not supported and it is recommend to explicitly disable QUIC protocol in web browsers."

 

MX:

SD-WAN Internet Policies (SD-Internet)

Change: Added note "For some UI features that you see in the sections below, MX18.2+ is required. MX devices on firmware versions below MX18.2 can still use the feature in the same manner but the UI view is slightly different."

 

SD-WAN and Traffic Shaping

Change: Added "MX95, MX105, MX85, MX75 Z1, Z3, Z3C, Z4, Z4C".

 

General MX Best Practices

Change: Added note that SD-WAN Policies only appear after Active-Active Auto VPN is enabled; added note "On MX18.2 firmware while using MultiWAN MXs SD-WAN policies and load balancing policies do not apply to WAN3."

 

MX Firewall Settings

Change: Added "The DNS request doesn't need to be from a specific client, the MX will map the FQDN based on the DNS response, regardless of which client made the DNS Request."; added "MX will not be able to snoop TCP-based or encrypted DNS traffic."

 

MultiWAN Backup Uplink

Change: Added VPN behavior for AutoVPN; added "IPv6 is not supported on the Backup WAN uplink".

 

Trusted Traffic Exclusions

Change: Added "The Cisco Meraki Cloud and Umbrella Cloud communications are trusted by default."

 

Security Center

Change: Added section "Organization-wide".

 

Using Layer 3 Firewall Rules

Change: Updated wording "Note that, on a network with an MX handling inter-VLAN routing, the IP address of the MX on the destination subnet may still respond to any services (For example: ICMP pings, SNMP, and so forth) it's configured to listen for, even if the rule is set to block traffic."

 

MS:

Getting started: Cisco Catalyst 9300 Management with Meraki Dashboard

Change: Added additional command required for cloud connectivity "ip http client source-interface {vlan-interface}"; added note "Do not use the OOB port (Gig0/0) management port on the rear of the switch for internet connectivity. Front facing ports only."; added note "SVIs only, no routed-port support at this time."

 

Setting Custom DHCP Options

Change: Added section "Unsupported DHCP options on MS390 and Meraki-managed C9300".

 

Link Aggregation and Load Balancing

Change: Added note "When configuring LACP port-channels on uplinks between remote switches/stacks, always configure the remote/downstream side of the port-channel first. Once the config has been applied configure the LACP port-channel on the upstream switch. This insures you don't strand the downstream switch. Catalyst 9300-M and MS390 switches will disable a port (for 30 seconds) if it detects a regular trunk port on the other end of a configured LACP port."

 

MS DHCP Servers

Change: Updated for IPv6 options.

 

Small-Form Factor Pluggable (SFP) and Stacking Accessories

Change: Added "C9300-NM-2Y-M / C9300-NM-2Y modules are supported only by C9300-24S/48S switches in firmware CS16.7(CS16GA2). Support for the rest of the C9300-M portfolio will be added in CS16GA3 firmware."

 

Switch Ports

Change: Added C9300-M.

 

Catalyst 9300-M Datasheet

Catalyst 9300X-M Datasheet

Change: Added note "The PWR-C1-1900WAC-P-M provides 1900 W output power when the nominal input voltage is 230 V. If the nominal input voltage is 115 V, then the output power is limited to 1500 W. The power supply does not work with standard 125VAC power cords (common with 1100W and lower power supplies), you require a C21 power cable."

 

Switch Settings

Change: Added "Assigning a static IP address and/or VLAN to a switch will override management VLAN settings configured on this page."; added "An Alternate Management Interface can also be configured to source management traffic such as Syslog messages and communication with RADIUS servers from a different VLAN."

 

FAQs: Migrate to Meraki management mode

Change: Added "This [the replacement of hardware] differs from CW access points where the replacement will be the same mode as when the case was opened."

 

MR:

Access Point Status Page

Change: Added "BSSID details for each SSID and current radio configuration (such as bands, channels, channel-width, and transmit power)"; added description for the Enabled and Broadcasting columns in the BSSID details window  (blue note).

 

RF Profiles

Change: Added "The individual selected bands in Wireless > Configure > Radio Settings > General > Band Selection do not reflect in the Enabled and Broadcasting columns of the BSSID details found in Wireless > Monitor > Access Points."

 

MR Mixed Firmware Networks

Change: Added Meraki Wi-Fi 6E access points.

 

Extending the LAN with a Wireless Mesh Link

Change: Added warning "Link aggregation on dual-port APs (e.g., MR52, MR53, MR53E, MR57, MR84) must be disabled to allow wired clients connected directly to the AP to gain network connectivity and pass traffic through the wired port on the AP."

 

MV:

MV13 Installation Guide

Change: Updated sections "Mounting Instructions" and "MV13 Install using the small mounting plate".

 

MV Presence Analytics

Change: Added section "Installation guideline"; added "Minimum software requirements"; added "The data for each configuration will retain for 6 months per area/line from the date of the configuration."

 

MV63 Series Datasheet

Change: Updated Field of View data; added Licensing options for MV Sense and Cloud Archive.

 

External RTSP

Change: Added MV13 and MV33.

 

Meraki Vision Portal Changelog

Change: Added release notes for up to v1.17.4.

 

SM:

Systems Manager Agent Release Notes

Change: Added release notes for up to v4.1.4.

 

Systems Manager Agent Upgrade 2024

Change: Added FAQ "What version(s) of the agent will clients be upgraded to?"

 

General Administration:

Throughput test to the Cisco Meraki Dashboard

Change: Added "Unidirectional or asymmetrical routing configuration" to section "Factors Affecting the Dashboard Throughput Test".

 

Returns (RMAs), Warranties and End-of-Life Information

Change: Added "Products must be returned to Cisco's designated location within 30 days of receiving your Returns Material Authorization (RMA) number."

 

Meraki Subscription Licensing Overview

Meraki Subscription Licensing - Subscription Claim

Meraki Subscription Licensing - Network Binding

Change: Updated for Subscription Changes.

 

Meraki MS Subscription Licensing

Change: Added MS130R.

0 Replies 0
Get notified when there are additional replies to this discussion.
Welcome to the Meraki Community!
To start contributing, simply sign in with your Cisco account. If you don't yet have a Cisco account, you can sign up.