Documentation Digest: December 13th - December 19th

Hannah-C
Meraki Employee
Meraki Employee

Documentation Digest: December 13th - December 19th

DocDigest_Banner.png

 

New articles:

Multicast Overview, Configurations and Best Practices

Change: New article.

 

Managing Unified Licenses in EA

Change: New article.

 

 

Secure Connect:

Cisco Secure Connect - Client-based ZTNA

Change: Added "DNS resolution for private apps will come from the ZTA enforcement node in the CGNAT space 100.64.0.0/10."

 

 

MG:

Cellular Gateway (MG) Firmware Features Directory

Change: Updated table "Stable Release - MG 3.212 Firmware Features".

 

 

MX:

Cisco XDR FAQ

Change: Added FAQ "How can I verify my MX/Z is sending telemetry to Cisco XDR?"; added FAQ "Who should I call if I have questions about an incident detected by Cisco XDR?".

 

MX Templates Best Practices

Change: Added section "IP Offset".

 

MX Warm Spare - High-Availability Pair

Routed HA Failover Behavior

Change: Added VRRP timer value (3 seconds).

 

Using Site-to-site VPN Translation

Change: Added "VPN NAT can be configured via API on firmware 19.1+."

 

Border Gateway Protocol (BGP)

Change: Added section "BGP Path Selection Attributes".

 

vMX Setup Guide for Amazon Web Services (AWS)

Change: Added "If return routes for these subnets are not added to the AWS VPC route table via the steps listed above, bi-directional communication between hosts in remote AutoVPN subnets and AWS resources will not occur, as return traffic will not be routed to the vMX."

 

BGP routing over IPsec VPN

Change: Added "Statically defined local routes configured on passthrough MX devices are not exported to the eBGP peer over IPsec."

 

 

MS:

Adaptive Policy MS Configuration Guide

Change: Updated SGT order of operation for classification.

 

MS130 Datasheet

Change: Added MS130 Licensing.

 

Cloud-Native IOS XE Overview

Change: Added C9300L models.

 

 

MR:

CW9176I Installation Guide

CW9176D1 Installation Guide

CW9178I Installation Guide

Change: Added "The Cisco Wireless CW917x series of Access Points is a Unified Hardware with a single product ID, that can be deployed with a Cisco Catalyst 9800 Wireless LAN Controller or Meraki Cloud based deployments. The CW917x series Access Points can be deployed anywhere in the world just with the single product ID (PID or SKU) and avoids the need to buy a region or country specific access point hardware based on regulatory domain. Please refer to the Global Use AP deployment guide for details."

 

CW9176I / CW9176D1 Datasheet

CW9178 Datasheet

Change: Added "Due to the 6 GHz band requiring PMF some Air Marshal functions may not be effective"; added peak antenna gain for the second 5 GHz antenna.

 

Wireless (MR) Firmware Features Directory

Change: Added "Intelligent capture" to section "MR 30.X Firmware Features"; updated description of the "Intelligent capture (Proactive PCAP)" in section "MR 31.1.X Firmware Features".

 

Low Power Mode

Low Power Mode on Cisco Switches

Change: Added "UPoE" to table "PoE Standards".

 

Splash Page Traffic Flow and Troubleshooting

Change: Added note regarding the splash URL: "In some configurations, [nX] may be replaced by a region-specific string. For example, networks located in the Asia-Pacific region may see the splash URL https://apac.network-auth.com/splash/?".

 

WPA3 Encryption and Configuration Guide

Change: Updated regarding Wi-Fi 7.

 

 

MV:

MV72 Series Installation Guide

Change: Added optional installation step 4 regarding the MV72's optional external grounding screw.

 

Meraki Vision Portal Changelog

Change: Added release notes for up to v1.23.6.

 

 

General Administration:

Product Firmware Version Restrictions

Change: Added Z3 / Z3C maximum firmware version.

 

Packet Capture Overview

Change: Added "Intelligent Capture is currently in the Early Access Phase. There is no MR-ADV license requirement for the Proactive PCAP feature during the Early Access Period. See the MR License Guide for more details."

 

Meraki Assurance Overview Page

Change: Added section "Configuration Changes Timeline".

 

Cisco Meraki Firmware FAQ

Change: Added note about sender e-mail address and recipients of the firmware upgrade alert email.

 

Managing Dashboard Administrators and Permissions

Change: Added section "E-mail Subaddressing".

 

FAQ for Call Me Now

Change: Added "Additionally, providing case details before connecting with phone support helps our Support team understand your issue and assign the most appropriate engineer for your case."

 

Dashboard Data Availability

Change: Added "Login attempts logs for up to the last 12 months can be requested by contacting Meraki Support."

 

Cisco Meraki Canada Region

Change: Added section "Accessing with Mobile App".

 

Viewing Old Event Logs

Change: Updated "Dashboard can maintain event logs for up three months, which can be viewed for historical purposes unless Network-Wide > Configure > General > Client privacy has been configured for a shorter timeframe."

 

Enterprise Agreements

Change: Added "Consumption will happen when a device is added to a Network associated with your EA, regardless of its active or inactive status. When a device is part of a network, it will trigger consuming a license."

 

2 Replies 2
PhilipDAth
Kind of a big deal
Kind of a big deal

I don't know how the team manages to publish so much documentation, but it is great to see.

RaphaelL
Kind of a big deal
Kind of a big deal

https://documentation.meraki.com/MS/Other_Topics/Multicast_Overview%2C_Configurations_and_Best_Pract...

There are no links attached to this part :

 

Please refer to the following articles for more information on L2 and L3 multicast:

Get notified when there are additional replies to this discussion.
Welcome to the Meraki Community!
To start contributing, simply sign in with your Cisco account. If you don't yet have a Cisco account, you can sign up.