Hello! In order to reduce the amount of API call.  Is it possible to implement a new api endpoint. Currently we are using the request below: GET /networks/[networkId]/devices/[serial]/performance (https://documenter.getpostman.com/view/897512/2To9xm#d96f2d50-b985-d626-ed5f-d768c14230b3) But as we have a lot of organizations and devices, we send a lot of HTTP get and we hit the API rate limit. Is it possible to have a GET with all MX score performance of a organizations? Maybe something like that HTTP Request : GET /organizations/[organizationId]/devicesMXPerformance Sample Response : [{     "Q2XX - XXXX - XXXX": "21" }, {     "Q5XX - XXXX - XXXX": "19" }] Thank you for your feedback. Regards ... View more

Hello everyone 🙂 !   I have a question about snmpwalk to meraki device MX68.   I would like to check interface traffic, through my ports, however, these information with snmpwalk are different from that I have in the Meraki dashboard.   In the Meraki dashboard, as you can see below, we  have the port 1 and 11 connected and up.     (Port 1 and 11 are connected and we traffic on these interfaces.)     However, the feedback on the snmpwalk show us the "OperStatus" 1 and 11 as down whereas they are up on the dashboard.     IF-MIB::ifOperStatus.1 = INTEGER: down(2)     According to cisco MIB, ifOperStatus is the current operational state of the interface. If ifAdminStatus is down(2) then ifOperStatus should be down(2).       OID   1.3.6.1.2.1.2.2.1.8   Module   IF-MIB (CISCO)   Nom   ifOperStatus   Acces   readonly   Status   current   Description   The current operational state of the interface. The testing(3) state indicates that no operational packets can be passed. If ifAdminStatus is down(2) then ifOperStatus should be down(2). If ifAdminStatus is changed to up(1) then ifOperStatus should change to up(1) if the interface is ready to transmit and receive network traffic; it should change to dormant(5) if the interface is waiting for external actions (such as a serial line waiting for an incoming connection); it should remain in the down(2) state if and only if there is a fault that prevents it from going to the up(1) state; it should remain in the notPresent(6) state if the interface has missing (typically, hardware) components.   Syntaxe   Enumeration (1-up, 2-down, 3-testing, 4-unknown, 5-dormant, 6-notPresent, 7-lowerLayerDown)         However, in my snmpwalk my ifAdminStatus is up but my ifOperStatus is down.       snmpwalk -v 3 -u 'XXX' -x des -X 'XXX' -A 'XXX' -a sha -l authpriv  AA.BB.CC.DD     IF-MIB::ifAdminStatus.1 = INTEGER: up(1) IF-MIB::ifAdminStatus.2 = INTEGER: up(1) IF-MIB::ifAdminStatus.3 = INTEGER: up(1) IF-MIB::ifAdminStatus.4 = INTEGER: up(1) IF-MIB::ifAdminStatus.5 = INTEGER: up(1) IF-MIB::ifAdminStatus.6 = INTEGER: up(1) IF-MIB::ifAdminStatus.7 = INTEGER: up(1) IF-MIB::ifAdminStatus.8 = INTEGER: up(1) IF-MIB::ifAdminStatus.9 = INTEGER: up(1) IF-MIB::ifAdminStatus.10 = INTEGER: up(1) IF-MIB::ifAdminStatus.11 = INTEGER: up(1) IF-MIB::ifAdminStatus.12 = INTEGER: up(1) IF-MIB::ifOperStatus.1 = INTEGER: down(2) IF-MIB::ifOperStatus.2 = INTEGER: down(2) IF-MIB::ifOperStatus.3 = INTEGER: down(2) IF-MIB::ifOperStatus.4 = INTEGER: down(2) IF-MIB::ifOperStatus.5 = INTEGER: down(2) IF-MIB::ifOperStatus.6 = INTEGER: down(2) IF-MIB::ifOperStatus.7 = INTEGER: down(2) IF-MIB::ifOperStatus.8 = INTEGER: down(2) IF-MIB::ifOperStatus.9 = INTEGER: down(2) IF-MIB::ifOperStatus.10 = INTEGER: up(1) IF-MIB::ifOperStatus.11 = INTEGER: down(2) IF-MIB::ifOperStatus.12 = INTEGER: down(2)     Moreover, we can some traffic through these interfaces: . . IF-MIB::ifInOctets.1 = Counter32: 4267233788 IF-MIB::ifInOctets.2 = Counter32: 0 IF-MIB::ifInOctets.3 = Counter32: 0 IF-MIB::ifInOctets.4 = Counter32: 0 IF-MIB::ifInOctets.5 = Counter32: 0 IF-MIB::ifInOctets.6 = Counter32: 0 IF-MIB::ifInOctets.7 = Counter32: 0 IF-MIB::ifInOctets.8 = Counter32: 0 IF-MIB::ifInOctets.9 = Counter32: 952818 IF-MIB::ifInOctets.10 = Counter32: 0 IF-MIB::ifInOctets.11 = Counter32: 3309773612 IF-MIB::ifInOctets.12 = Counter32: 0 IF-MIB::ifInUcastPkts.1 = Counter32: 316592390 IF-MIB::ifInUcastPkts.2 = Counter32: 0 IF-MIB::ifInUcastPkts.3 = Counter32: 0 IF-MIB::ifInUcastPkts.4 = Counter32: 0 IF-MIB::ifInUcastPkts.5 = Counter32: 0 IF-MIB::ifInUcastPkts.6 = Counter32: 0 IF-MIB::ifInUcastPkts.7 = Counter32: 0 IF-MIB::ifInUcastPkts.8 = Counter32: 0 IF-MIB::ifInUcastPkts.9 = Counter32: 2829 IF-MIB::ifInUcastPkts.10 = Counter32: 0 IF-MIB::ifInUcastPkts.11 = Counter32: 390020574 IF-MIB::ifInUcastPkts.12 = Counter32: 0 IF-MIB::ifInNUcastPkts.1 = Counter32: 0 IF-MIB::ifInNUcastPkts.2 = Counter32: 0 IF-MIB::ifInNUcastPkts.3 = Counter32: 0 IF-MIB::ifInNUcastPkts.4 = Counter32: 0 IF-MIB::ifInNUcastPkts.5 = Counter32: 0 IF-MIB::ifInNUcastPkts.6 = Counter32: 0 IF-MIB::ifInNUcastPkts.7 = Counter32: 0 IF-MIB::ifInNUcastPkts.8 = Counter32: 0 IF-MIB::ifInNUcastPkts.9 = Counter32: 0 IF-MIB::ifInNUcastPkts.10 = Counter32: 0 IF-MIB::ifInNUcastPkts.11 = Counter32: 0 IF-MIB::ifInNUcastPkts.12 = Counter32:     Do you know why we have this please?      Regards,   NicoSnmp ... View more

Hello,   I m trying to get response from snmpwalk for MS.   We can have a response from the OID '.1.3.6.1.4.1.29671.1.1.4' from devtable (for MS).    Here is our request:   for i in $(seq 1 14) ; do echo -e "$i"; snmpwalk -v 3 -u 'user' -A 'password' -a SHA -X 'privacy password' -x AES n143.meraki.com:16100 -l authpriv  .1.3.6.1.4.1.29671.1.1.4.1.$i.$MAC -O n; done 1 .1.3.6.1.4.1.29671.1.1.4.1.1.MACAddress = Hex-STRING: MAC Address 2 .1.3.6.1.4.1.29671.1.1.4.1.2.MACAddress = STRING: "MS1 Name" 3 .1.3.6.1.4.1.29671.1.1.4.1.3.MACAddress = INTEGER: 1 4 .1.3.6.1.4.1.29671.1.1.4.1.4.MACAddress = Hex-STRING: MAC Address 5 .1.3.6.1.4.1.29671.1.1.4.1.5.MACAddress = INTEGER: 3 6 .1.3.6.1.4.1.29671.1.1.4.1.6.MACAddress = No Such Object available on this agent at this OID 7 .1.3.6.1.4.1.29671.1.1.4.1.7.MACAddress = IpAddress: A.B.C.D 8 .1.3.6.1.4.1.29671.1.1.4.1.8.MACAddress = STRING: "serial number" 9 .1.3.6.1.4.1.29671.1.1.4.1.9.MACAddress = STRING: "MS220-8P-HW" 10 .1.3.6.1.4.1.29671.1.1.4.1.10.MACAddress = STRING: "Meraki MS220-8P Cloud Managed PoE Switch" 11 .1.3.6.1.4.1.29671.1.1.4.1.11.MACAddress = STRING: "MS1 Name" 12 .1.3.6.1.4.1.29671.1.1.4.1.12.MACAddress = No Such Object available on this agent at this OID 13 .1.3.6.1.4.1.29671.1.1.4.1.13.MACAddress = No Such Object available on this agent at this OID 14 .1.3.6.1.4.1.29671.1.1.4.1.14.MACAddress = No Such Object available on this agent at this OID     Nevertheless, we can get feedback from all OIDs  '.1.3.6.1.4.1.29671.1.1.5.1' from devInterfaceTable for MS.     Here is our snmwalk:   snmpwalk -v 3 -u 'user' -A 'password' -a SHA -X 'privacy_password' -x AES n143.meraki.com:16100 -l authpriv  .1.3.6.1.4.1.29671.1.1.5.1 -O n | grep -i "MAC address" . . .   These OID work with MX and MR but not with MS.   We configure snmpv3 through Organization>Configure>Settings.   Could you help me please?   Do you see something wrong with the snmpwalk ?   Regards   ... View more