Thanks for the reply. So having spoken to support, they were not aware of any issues. That being said, I opened a new ticket and another support agent came back to me and confirm it was maintenance.  Is there an easy way of knowing this before hand?   Thanks. ... View more

Currently speaking with support. They are informing me there is no issue and they can't explain it? Would this be an issue with all different ISP's? ... View more

**Update**   I visited site today as the Teltonika failed again last night. Having swapped the Teltonika for the RUT240 model I have configured it with the following:   The router is showing connected and ready to go in the event of a WAN1 failure. That being said, I have also configured the WAN2 settings to the following:   Connection Type: Direct IPV4 Config: Auto   Having got the IP address of the Teltonika, 192.168.1.1, I have input a "Flow Preference" as below:   The good news is I can now see the Teltonika on the network internally using a client PC.   The only issue I now have, I can't access the Teltonika from the VPN. I have input the destination in the client routing page on the VPN, but the page just times out. If anyone can shed some light on this that would be great.   Will test the connection tonight and see if it drops.  ... View more

Thanks for the reply. I will have no choice but to head over to site tomorrow and see what's going on. I have got another Teltonika, the RUT240, set this up with another MX64 and done some tests. It seems to be working ok, but will check tomorrow and report back.    Thank you. ... View more

When you say put it on DHCP, do you mean the router on WAN2?    I thought this router needed to be set with a static IP address? We can't had this back to the ISP as we have just bought the router on its own and inserted the 4G sim.    The WAN IP on the 4G sim will change as it's not static, but our client does not want to pay for a static IP.  This use to work perfectly when using a 4G dongle, but we wanted to use a better 4G device so went with the Teltonika TCR100 router. I'm still sure this is an issue with IP addresses, internally on our setup for this. The WAN side should not matter.   I appreciate your help.  ... View more

Thanks for the reply.   I understand what your saying, but is there a reason why I can't access the router interface within the network? I have VPN access all setup and put the route on the VPN. Even if I try and access the router interface within the network, I get a time out error.   Also, I have to keep rebooting my MX64 as it seems the WAN2 connection stops and goes to 100% loss according to the dashboard.   ... View more

Thanks for the reply. I don't think I'm explaining myself very well.   WAN1 - Works, no issues, provided with external company, using Openreach Modem (white box)   WAN2 - Kind of works, doesn't allow access to external modem, which is a full router and not a bridge router etc.   I need to know if WAN2 router needs to be set in bridge or passthrough mode? What IP address information do I input on WAN2 connection on the MX64?    Currently I have set the following:   Type - IPV4 Configured As - Static Status - Ready IP Address - 192.168.0.1 Subnet - 255.255.0.0 Gateway - 192.168.5.3 DNS - 8.8.8.8,  4.4.4.4 ... View more

Hello and thanks for the reply (Merry Christmas).   Just had too much to eat and decided to fire up the laptop and saw your response.   The reason I think my IP config is not right as I'm not totally confident on what I put. As I have another router and not just a bridge, I'm pretty sure my settings are not right.   Are you able to guide me with this at all please? At present it does work, but come midnight, the MX shows 100% loss and then I end up having to reboot things etc.   I will have to visit the site and try to figure this out, so any help I can get is appreciated. We had a normal FTTC connection on WAN2 before, so I knew what to put.   Thank you in advance and Merry Christmas.     ... View more