Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
About Paul_N
Paul_N
Here to help
Member since Nov 29, 2022
Dec 14 2022
Community Record
5
Posts
0
Kudos
1
Solution
Badges
Dec 4 2022
2:05 PM
Hi Karstenl, Thanks for your reply. I checked, and ACLs are mapped to an SVI that is not used anymore. So I don't need to Map them! Appreciate your time and help:)
... View more
Dec 4 2022
2:03 PM
Hi Brash, Thanks for your reply. I checked, and ACLs are mapped to an SVI that is not used anymore. So I don't need to Map them! Appreciate your time and help:)
... View more
Nov 30 2022
8:42 PM
Hi All, I have a Cisco 3750, which is moving to an MS425. There are some old ACLs, and I don't know how to convert them into MS425. ! ip access-list AAA permit 10.x.x.x 0.0.0.255 deny 10.x.x.x 0.0.0.255 deny 10.x.x.0 0.0.0.255 permit 10.x.x.0 0.0.3.255 permit 172.x.x.x0.0.0.31 permit 10.x.x.0 0.0.0.255 permit 10.x.x.0 0.0.0.255 permit 10.x.x.0 0.0.0.127 permit 10.x.x.0 0.0.0.255 permit 10.x.x.0 0.0.0.255 permit 10.x.x.0 0.0.0.255 permit 10.x.x.0 0.0.0.63 deny any log This is what I have on MS at the moment, which has no ACL: What would be the source, destination, and port for such a cisco ACL? Regards, Paul
... View more
Nov 30 2022
1:57 PM
Hi Alemabrahano, Thanks for your reply. My switch is already operational as an L2 switch and connected to my 3750. I am using this 3750 for routing and reaching the internet via DC. I need to retire the 3750, and as soon as I change the port from 3750 to MS425, I will lose the connection to the internet. Now, if I configure everything correctly, I should be getting connected back if bypass the 3750 and go direct to my WAN router(career already is ready for my route change) In this scenario, do I get an internet connection if I connect any LAN port to my Netgear 4G router, which has access to DHCP? Do I need any config change on the LAN port I want to use to connect my MS to the Netgear 4G(RJ45)?
... View more
Nov 29 2022
9:36 PM
Hi Guys, I want to move my routing from a cisco 3750 to my MS425 to get rid of the Cisco switch. I don't have physical access and need to work remotely. I have planned to create an L3 Uplink under my transit VLAN, assign a physical port to uplink, and ask someone on site to change the cable from 3750 to ms425 new uplink port. On paper, if I get everything right, it should come up after the cable change, but I want to have plan B and use a Netgear 4g router in case the MS switch loses connection to the network. The 4G router is rj45. Which interface could I use, and do I need any config on that int? Sorry if my question seems basic. Regards, Paul
... View more
Labels:
- Labels:
-
Interfaces
-
Layer 3
-
Other
My Accepted Solutions
| Subject | Views | Posted |
|---|---|---|
| 1863 | Dec 4 2022 2:05 PM |
© 2024 Cisco Systems, Inc.
