Meraki

Community
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Show  only  | Search instead for 
Did you mean: 

About DrRasmussen

Re: MX67 fail to upgrade

by in Dashboard & Administration
‎Dec 25 2021 11:11 AM
‎Dec 25 2021 11:11 AM
Perfect - thankt you - I'll send you the serial number in minutes 🙂   Br, Michael ... View more

MX67 fail to upgrade

by in Dashboard & Administration
‎Dec 25 2021 10:47 AM
‎Dec 25 2021 10:47 AM
After removing a MX67 running MX17.3 from a network in Dashboard - no psysical movement or disconnets, then I added the device into a new created network - a downgrade to MX15.44 happend.   The device are fuctioning well, but I need to use AnyConnect therefore at least MX16.xx is required.   When I try to upgrade, the I got the following message:   here were errors in saving this configuration: Firmware Upgrade failed due to the following node_groups: XXXXXXXX. Firmware Versions MR 28 and MX 16 require nodes to be able to contact Meraki's Device to Cloud Connectivity service over TCP port 443. One or more of your Meraki devices are unable to communicate with these new servers. For more information about this upcoming change and how to resolve the connectivity issue, please go to https://documentation.meraki.com/General_Administration/Cross-Platform_Content/Meraki_Device_to_Cloud_Connectivity_-_FIPS.   What to do?   Best regards, Michael   ... View more

Re: Guest Net on specific public IP

by in Security & SD-WAN
‎Mar 10 2021 6:32 AM
‎Mar 10 2021 6:32 AM
Great - thank you. I have just upgraded to version 15.42. I can't find any configuration examples - and unfortunately I have no lab Meraki device with 2 WAN's her.   My installation is 4 hours drive away - so I have do no configuration mistakes.   Is it possible to place WAN1 and WAN2 in same subnet from ISP - or shall the ISP devide the subnet into two?   Br, Michael ... View more

Re: Guest Net on specific public IP

by in Security & SD-WAN
‎Mar 9 2021 12:45 PM
‎Mar 9 2021 12:45 PM
Thank you all. I'll look into it.   I rise another questieon. It is my customer who is asking for a setup like this, where guest traffic have a another public source IP address.He said it's for securityr reasons, not to let the public IP be "too public"   Howerever: Is there a best year 2021 practice. Is it nescasarry to seperate guest traffic to another public IP or is it old school? The MX is licenced for Advanced Security. ... View more

Re: Guest Net on specific public IP

by in Security & SD-WAN
‎Mar 9 2021 12:02 PM
‎Mar 9 2021 12:02 PM
Hi @GreenMan    What do you mean with "Although you could connect WAN1 and WAN2 of your MX via the same uplink"? Can I use the same physical interface? Isn't there a really simple solution here. I don't think I'm the one and only looking into this kind of problems.     /Michael ... View more

Re: Guest Net on specific public IP

by in Security & SD-WAN
‎Mar 9 2021 6:16 AM
‎Mar 9 2021 6:16 AM
Hi @DarrenOC    First of all thank you for helping me here.   As I understand WAN1 and WAN2 in the same subnet.   WAN1: A.B.C.1 Gateway A.B.C.X WAN2: A.B.C.2 Gateway A.B.C.X   Which means that the two WAN's are using same gateway?   Control of which WAN link to be used for guest net is done via SD-WAN & Traffic shaping?             ... View more

Guest Net on specific public IP

by in Security & SD-WAN
‎Mar 9 2021 4:59 AM
‎Mar 9 2021 4:59 AM
Hi I have a MX84 I have one public IP - lets say x.x.x.1, which I use for internet traffic. I have a Guest WIFI VLAN - I need to use another public IP for guest traffic - lets say x.x.x.2   How can this be done in Meraki MX devices?   ... View more
© 2024 Cisco Systems, Inc.