Meraki

Community
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Show  only  | Search instead for 
Did you mean: 

About radw62

Re: MX64 Flow Preferences - Internet traffic rules not work

by in Security & SD-WAN
‎Jan 24 2018 7:18 AM
2 Kudos
‎Jan 24 2018 7:18 AM
2 Kudos
@PhilipDAth wrote:   Lets try one more test.  Lets use a web site like: https://www.whatismyip.com/ Find out what the IP address is for this from your location.  Then create a rule to route this out WAN2.  Then visit the web site.  Does it come up with the public IP address for WAN1 or WAN2? Hello, I tried this config, and it worked (It shows WAN2 ISP address as my Public IP according to flow preferences policy). Thanks for the hint. ... View more

Re: MX64 Flow Preferences - Internet traffic rules not work

by in Security & SD-WAN
‎Jan 21 2018 8:29 AM
‎Jan 21 2018 8:29 AM
Hello, my answers:   @PhilipDAth wrote: Does WAN2 show as "up" in the Appliance Status - like WAN1?  It should display the detected public IP address next to WAN2 if it is.  Yes, it does show as "up":       @PhilipDAth wrote: What source IP address where you doing the traceroute from?   @PhilipDAth wrote: I have made one giant assumption.  How do you know your traceroute is going via WAN1?   I do the traceroute from a host on 192.168.128.32/28. From this host the trace exits over the WAN1 next hop (192.168.100.1), not WAN2 next hop (192.168.1.1😞           ... View more

Re: MX64 Flow Preferences - Internet traffic rules not work

by in Security & SD-WAN
‎Jan 18 2018 7:29 PM
‎Jan 18 2018 7:29 PM
Hello, here are the traffic shapping screenshots:     @PhilipDAth wrote:     The change takes affect for new flows, not existing cached flows.  You can power cycle your MX64 to speed it up.   I performed a MX65 reboot after re-create rule but still not work.     @PhilipDAth wrote: Are you sure me mean 0.0.0/6?  That is not valid CIDR.    Sorry, maybe copy-paste not worked (I defined flow preferences to 52.0.0.0/6 from beginning)   Regards ... View more

MX64 Flow Preferences - Internet traffic rules not work

by in Security & SD-WAN
‎Jan 17 2018 6:14 PM
‎Jan 17 2018 6:14 PM
Hello Meraki Community: I have a MX64 version MX 12.26 with two connections to different ISP, Internet (WAN1) and LAN4 (WAN2). I want to send all traffic from two VLANs to 0.0.0/6 via WAN2 uplink (any SRC and DST port), but when I created on Traffic Shapping – Flow Preferences - Internet traffic that rule, all traffic and tracerutes to 52.0.0.0/6 still goes out via WAN1 I have load balancing disabled (because I don’t want load balancing between ISPs yet, and doc and dashboard description both confirm that flow preferences will precede load balancing preferences: https://documentation.meraki.com/MX-Z/Firewall_and_Traffic_Shaping/MX_Load_Balancing_and_Flow_Preferences) , however, even enabling it and tuning different WAN1/WAN2 ratios, traffic still goes to WAN1, and the Flow Preference Rule that I want don’t work , and I have no other choice than force WAN2 to be the Primary Uplink Regards ... View more
© 2024 Cisco Systems, Inc.