Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Register or Sign in
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
About celma972
celma972
Comes here often
Member since Sep 23, 2019
Jan 12 2024
Community Record
17
Posts
0
Kudos
0
Solutions
Badges
Jun 5 2021
12:23 AM
Hi Bruce, Trunk and ip helper-address are setup already. VLAN 2 clients and VLAN 1 clients are receiving DHCP ip addresses. But I am still seeing on the meraki dashboard logs : client made a request to the DHCP server, but it did not respond Client attempted to associate 265 times on the 2.4 GHz band Can this be a result of roaming between AP, bad coverage, etc....? Thks
... View more
Jun 3 2021
9:31 AM
Dear All, I am seeing frequently the following message on my meraki dashboard event log : client made a request to the DHCP server, but it did not respond Client attempted to associate 265 times on the 2.4 GHz band The AP are MR33 firwmware version 28.1 There are two SSID VLAN : - VLAN 1 is for datas and is used by RF Android scanner devices. - VLAN 2 is used for voice by client devices with Android Crosscall smarphone VLAN 1 and VLAN 2 subnets are not the same DHCP server for both subnets is a Windows 2016 server. It is on VLAN 1. routing between subnet is working. Scanner devices connected to VLAN 1 are getting DHCP IP from VLAN 1 Voice devices connected to VLAN 2 are getting a DHCP IP from VLAN 2 there are 33 AP MR33. So, the client devices are roaming. Do you know how can I fix that ? Do you know how can I setup on a cisco L3 switch that VLAN 2 will be voice only nothing else, is it possible? I set this command switchport voice vlan but I am not sure if it prohibit datas flow. Thks in advance
... View more
May 20 2021
11:23 AM
Hi Kudos, Are you taklking about the switchport command on the switch?. If yes, I know that one. But I am trying to understand this "all other APs"
... View more
May 20 2021
8:40 AM
Hi I have 30xMR33 in my warehouse all of them are setup with a SSID using radius. This SSID is used for Data only and is on the native VLAN (vlan 1). I have added and setup a new SSID for Voice only I would like the additional SSID use the VLAN 2 for Voice. Is it the correct configuration to have on all the 30xAP for both SSID working for wireless datas and voice equipements working? Our switch are Cisco 2960. I can ping the voice and the data subnet from the AP. this is the show Vlan on the core switch IWRcore#sh vlan VLAN Name Status Ports ---- -------------------------------- --------- ------------------------------- 1 default active Gi1/0/2, Gi1/0/3, Gi1/0/4 Gi1/0/5, Gi1/0/6, Gi1/0/7 Gi1/0/8, Gi1/0/9, Gi1/0/10 Gi1/0/11, Gi1/0/12, Gi1/0/15 Gi1/0/16, Gi1/0/17, Gi1/0/18 Gi1/0/19, Gi1/0/20, Gi1/1/2 Gi1/1/3, Gi1/1/4 2 SUB_109_ active Gi1/0/21, Gi1/0/22 1002 fddi-default act/unsup 1003 token-ring-default act/unsup 1004 fddinet-default act/unsup 1005 trnet-default act/unsup VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2 ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------ 1 enet 100001 1500 - - - - - 0 0 2 enet 100002 1500 - - - - - 0 0 3 enet 100003 1500 - - - - - 0 0 1002 fddi 101002 1500 - - - - - 0 0 Thks in advance
... View more
Apr 26 2021
3:10 AM
Hi Bruce, The AP are used for Androids Gun, Forklift terminals and VoCollect talkman terminals in the warehouse. We are using the 2.4Ghz band for them. This is the configuration According to the elements I have given, can you help me to establish an action plan to use the existing APs with Android mobile phones without a SIM card (I would only like to use WIFI). Knowing that the APs are Meraki MR33s located at about 15m height from the ground. We had already carried out a site survey for the installation of guns, forklift and Voicecollect terminak three years ago. Thks for your help
... View more
Apr 19 2021
3:41 PM
Hi cmr, I will have the same issue if I am on bridge mode, because the voice devices will roam as well, correct?
... View more
Apr 19 2021
2:41 PM
Dear all, We have 33 x Meraki MR33 placed at 15 meter height from the ground in a warehouse. We are using the 2.4Ghz band with one SSID for the RF devices (Android guns and forklift terminals). We create a new SSID with the following settings for Android smartphone son which we are using a Voip softphone The issue we are experiencing is we have choppy calls and poor quality voice. Could you give some clues how to optimize the calls? Thks
... View more
Oct 10 2019
9:19 AM
By changing the SSID only I can reduce the interfarence? But the AP will still up and propagating signal
... View more
Oct 10 2019
9:14 AM
Cmr, We have a mix of 802.11b and 802.11g RF devices. So, setting the minimun bit rates down would be 11Mbs. We are using the same SSID for the 33 x MR33.The radius server is Windows 2016 domain controller. I will try your suggestion when I will be onsite the next time. Thks
... View more
Oct 9 2019
9:45 AM
Hi SergeD, The terminal are inside the forklifts. The forklift has no thick glass and caging. This is the forklift we have and you can see the terminal The AP height are installed at 12m from the floor Power level for all AP is :
... View more
Oct 9 2019
9:18 AM
Hi cmr, Thks for you suggestion. I already lowwer the birates at 11mb minimun. We don't have RF devices supporting 5GHz. We have enabled both band We are not using 5GHz band because we don't have RF devices supporting it. In this case is it better to set the 2.4 GHz only?.
... View more
Sep 30 2019
9:29 AM
We are using one SSID for the 33 x MR33 APs. 'separation between band -> do you mean channel? We have set auto channel. So, all Aps are using channel 11,6,1. And these 3 channels are theorically not overlapping We do not set channels manually. We are using the 2.4 ghz band because the RF client devices are supporting 802.11b and 2.4 Ghz only .
... View more
Sep 30 2019
9:14 AM
I'm thinking about driver issue from the RF client. Could it be one reason for latency on the client itself?
... View more
Sep 30 2019
7:35 AM
Hi NolanHerring, The RF devices are supporting 2.4 GHz only. The latency are on the truck terminals only. Because the locked with a LCK-H (meaning waiting for host response) for at least 4 mn. The others RF devices are fine. This is the wireless health :
... View more
Sep 30 2019
6:59 AM
Dear All, We have installed 33 x MR33 into our Warehouse. They replaced old Cisco 1240AG AP. The clients devices are guns, truck terminals and voice terminals. We are not having latency issues on the guns and voices terminals but only on the truck terminals. I have disabled load balancing, the MR33, set the mininum bit rates at 11, disabled 802.11ax, enabled dual band operation 2.4 and 5 ghz, disable band steering. We are still having latency on the truck terminals and 13 x MR33 Do you have any idea how I can fix the latency issue? Thks JC
... View more
© 2024 Cisco Systems, Inc.
