Hi Philip, Thanks for the Link. It solved the way we addressed the Problem. We had the routing on the MX as designed. After a request of Multicast we needed 2 Interface on the Switch. And just as Karstenl says don't like the Idea that the switch is tarting routing also. Thanks for the Link. ... View more

Thanks for the Tip. I hoped there is something like Netflow 😞  ... View more

Yes, but 🙂 you see where the traffic goes to but not from where it comes 😞 even if you export it to excel you denote have more infos. ... View more

It is written that this policy will be applied to all client in this VLAN. SO if I add a bandwidth of 100MB in this Policy each client will get 100MB but I want 100MB for all client in this Network (VLAN) ... View more

I am in the same Status. As the Firmware with solves a lot of Problems is still Beta I do not recoment to buy it now. Or only if you need Multigigabit Ports. One of the biggest problem still is that if you have a stack with ms390 and you are updating software the full stack goes down!! and not just for 3 Minutes. Last update of a stack with 4 MS390 took more that 35 Minutes to get fully operational again.   I also See that Meraki is using more Cisco Nativ switches in future. But if you see how it is implemented at the moment. this will never work stable. if you open the MS390 Switch you find the Serial Console Port. Connect a Console Cable to it and power on the switch. You are able to see that the Switch is powering up a Cisco nativ IOS and then starting a virtual stack for the Meraki implementation. ... View more

@PhilipDAth we have a big multinational Pharma Company in Switzerland wich want to monitor more close temperature  in rooms.     We want to create a Dashboard (Like the VideoWall) but with all temperature sensors where we see all temperature of all rooms. (if possible in real time).   Actual with the setup the temperature sensor works there can be a delay of up tu 20 minutes until you have the values, and the Delay between 2 measurements is 2 minutes. This is absolutely ok if you are running on Batery mode. but it would be perfekt to have like all 30 seconds measurement in realtime id the sensor is connected to USC C Power. I did already a "Make a Wich" 🙂   regards Michel ... View more

Hi David,   This is Perfekt, now I don't get anymore alerts during the day 🙂 Thanks for That. But I Just have a very big Wish!   Please make it possible to get the Temperatur information more often like all 30 Seconds if the Sensors is connected to USB C Power Supply. (you don't need anymore to same Battery Live)  WE want to be able to detect a Temperatur Chance within a short time.  for example alert if the temperature goes up more that 5 Cellius with 2 Minutes.  We could do this true api but actually the temperature infos you get true API could be in worst case 20 Minutes old, and with a 2 Minutes time frame.   is it a big thing to add this?   regards Michel Rueger ... View more

I just do Testing with MS14.8 Beta on my MS390 and yes there are some updates Like Power supply information but still a lot of things not working. Client Information is now OK. But you can not have more than 3 Switches in a Stack with Beta 14.8!!   Kabel Test is not Working. Ping from the Switch goes up to more than 400ms and sometimes even up to 2 seconds!   hope to be able to post more updates soon. ... View more

I am on the last Beta Software an still no Support for IP V6!! only Pas true Modus. I agree with all of you since Meraki has joined Cisco it is not going better. ... View more

WE did a lot of Iperf, but didn't find-out what the problem is. From a Macbook Pro to the Mac Mini (WLAN to LAN)     First Images is Iperf from Laptop (LAN) to MAc mini (LAN) second Images is Iperf from Laptop (WLAN) to MAc mini (LAN)   What we see is that the speed is very unstable. ... View more

Hi,   I have the Same Problem at the Moment with MR46 AP. I do not get more that 130Mbps true WLAN. If I connect the Macbooc or a Lenovo Laptop to the same Switch with Kabel I have full gigabit Speed.   I did already a lot of Testing an it is a little bit better with a Ubiquit AP but still not what it should be. I also do Speed-test with IPERF between a Mac Mini and the Laptops.   If I do the Speed-test from a Laptop connected to the Ethernet Kabel to the Mac Mini I gor full speed, so I dont think it is a Problem of the LAN Port from the Mac Mini. ... View more

14.6 ?  the newest Release i see for Switches is MS12.28   now biggest Stack is 3 Switches. ... View more

Just want to give a update to MS390. There are still a lot of Dashboard Problems with this Switch,   * No Power-supply Information * Wrong Port Information in the Client View * Network Wide Topology completely wrong information * No Packet Capter posibility as Switch is delivering wrong Port Information * Log File Show 1'000 of wrong Port Change * ...   TAC is not solving the Problems they gibe it all back to Development. Cases are open since more than 2 Mounts and nothing happen 😞   We did escalated it true Meraki sales to management but nothing happen.     ... View more

You are perfect thanks.     ... View more

So I am Using the Last Beta Software and it is stable. The good Think with this Beta is you see the Module Interface Status.     ... View more

Hello MS390 Guys,   I have the next very Strange thing about that Switch. As you can see in the Pictures if you Stack two Meraki (True Meraki Switches 🙂 ) together they have there own IP See MS450 Core Stack but if you stack MS390 they Lose there preconfigured Statik IP Adress and get one of the Stack Member IP. I didn't figured out witch IP the Stack is selecting but all switches in the Stack have the Same IP. SO there is no consistency how Meraki is Managing Stack IP Addresses. Or better told if you don't use MS390 there is a consistency and if you use the MS390 you loos them 😞                               There is also something absolutely strange If you are using Stack with MS390 the Network Topology is changing every 10 Minutes 🙂   So Stay tuned for Updates. ... View more

Just got News on this.   If you upgrade to MS12.22 Beta Software you have one think fixed. The Stack Modul is now Showing correctly.   Before MS12.22         After MS12.22 update        Power information are still not there but Development is working hard to get it fixed 🙂 ... View more

Now we go live with 12 * MS390, but it is just a nightmare. The Switch are not correctly show in the Network overview and the Power Supply Infos from the Switch are just not existing.        This is now a long time the Switches are sold and still this Problems ????????? ... View more

Hi,   I also would Use the MR74 and why are you not Putting the one one with is close to the building on LAN and a second MR74 just on power at the end of the Parking slot as repeater so you are sure to cover them all. have a look at this:  https://documentation.meraki.com/MR/WiFi_Basics_and_Best_Practices/Wireless_Mesh_Networking    I have done this several times and it works perfekt.   regards Michel ... View more

It don't seems to be on there urgent task list to fix this Problem 😞 this is wat i get yesterday from the TAC.   ************************************* Greetings Michael, I currently have not received any news from our development team regarding this unexpected behavior. However, be assure that as soon as I receive some news, I will convey the information to you. As an additional step, I could suggest contacting your sales representative so they can further engage the development team regarding this behavior if the matter is urgent. Please let me know if you have additional questions.   ***************************************   Shocking 😞  ... View more

No, I just updated the case and did some pressure on telling them the link to this discusion. keey you updatet ... View more