The Meraki Community
Register or Sign in
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Show  only  | Search instead for 
Did you mean: 
  • About GrantWilson
GrantWilson

GrantWilson

Just browsing

Member since Aug 6, 2019

‎08-23-2019

Community Record

3
Posts
0
Kudos
0
Solutions
Latest Contributions by GrantWilson
  • Topics GrantWilson has Participated In
  • Latest Contributions by GrantWilson

Re: Meraki VPN Client ?

by GrantWilson in Security / SD-WAN
‎08-19-2019 01:16 AM
‎08-19-2019 01:16 AM
@PaulRusso wrote: Are you using the DNS address to connect or the IP address? Do you have any other 3rd party VPN software installed?   You may want to check out this article here: https://documentation.meraki.com/MX-Z/Client_VPN/troubleshooting_essay_client_VPN#Windows_Error_789 See below: Windows Error 789 Example event log entries: Jul 2 13:53:20 VPN msg: invalid DH group 19. Jul 2 13:53:20 VPN msg: invalid DH group 20.   This issue may also result in no event log messages, if the client's traffic doesn't successfully reach the MX's WAN interface. Possible causes and solutions: Incorrect secret key (pre-shared key in Windows) Solution: Ensure that the shared secret is configured correctly on the client machine. It must match between the MX and the client. More information about setting the shared secret can be found in the links at the top of the page. Firewall blocking VPN traffic to MX Solution: Ensure UDP ports 500 (IKE) and 4500 (IPsec NAT-T) are being forwarded to the MX and not blocked. If traffic cannot reach the MX on these ports, the connection will timeout and fail. IKE and AuthIP IPsec Keying Modules disabled (Windows only) Solution: This occurs most often when 3rd party VPN software has been installed and disables the IKEEXT service. This can be re-enabled by navigating in Windows to Control Panel > Administrative Tools > Services. Find the service named "IKE and AuthIP IPsec Keying Modules" and open it. Change the Startup type to "Automatic". If this automatically reverts to "Disabled" or fails to start, it may be necessary to remove the 3rd party VPN software:   Hello Paul,   I'm also getting error 789. I removed the 3rd party VPN. Should I also switch the DNS server? Is it possible that the firewall may block the VPN traffic to the Meraki MX appliance? ... View more

Re: Can I use Cisco AnyConnect with Meraki Client VPN?

by GrantWilson in Security / SD-WAN
‎08-08-2019 05:01 AM
‎08-08-2019 05:01 AM
@Warren wrote: https://documentation.meraki.com/MX/Client_VPN/MX_security_audit_failed_fast essay_recommended_steps I'd say that this is as official of a response as there is likely going to be.   Hello,   Thank you for the source. Is there any way to configure Windows 10 to use the IKEv1 aggressive mode? After the Windows 10 update, I noticed that the connection switched from PAP to MSCHAP (just as mentioned by TMRoberts). ... View more

Re: Client VPN not working (MX64)

by GrantWilson in Security / SD-WAN
‎08-06-2019 10:38 PM
‎08-06-2019 10:38 PM
@mtint wrote: Hello,   I followed the client vpn setup as in the guide - https://documentation.meraki.com/MX/Client_VPN/Client_VPN_OS_Configuration   and followed TS  steps   https://documentation.meraki.com/MX/Client_VPN/Troubleshooting_Client_VPN#client_id_cheapessays#Windows_Error_789   I am unable to get this working.   Testing this from my iphone    Michael   Hello,   I have the same issue on Windows 10. It's giving me Windows 809 error message. Is there any way to get PowerShell scripts that could create a split tunnel by default? Thanks. ... View more
Powered by Khoros
custom.footer.
  • Community Guidelines
  • Cisco Privacy
  • Khoros Privacy
  • Privacy Settings
  • Terms of Use
© 2023 Meraki