Register or Sign in
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
- About hmc25000
Community Record
14
Posts
2
Kudos
0
Solutions
Badges
09-15-2022
09:33 AM
When will these Adaptive policy & SGT features be available on Meraki MX appliances? Better yet is there a Cisco or Meraki adaptive policy & SGT aware application that can be run on virtual machines?
... View more
01-20-2022
10:22 AM
Thanks. I'm a little confused with method 1 from the document. If I understand it correctly the Method 1 can be done "Adding the Replacement MX to the Same Network" or "Adding a Second MX to Form a Warm Spare Configuration". I understand for both you have to remove the old MX prior to adding the new one. How can you add a warm spare if you have removed the old MX? Can I assume there will be no downtime when I add the new as a warm spare and than remove the old MX? I just want o make sure I understand it correctly.
... View more
01-14-2022
09:34 AM
I need to swap out our 250 MX because of an issue with the current one crashing. Reading the documentation I'm inclined to assume that configuring a warm spare might be easier and have less downtime than doing a cold swap. Can anyone with experience recommend what the best way is with the least amount of downtime.
... View more
07-06-2021
12:37 PM
Is there a way to configure VPN client connections with MFA text code rather then notifications through the app? This might be a windows thing but figured I would ask if someone got it to work. MY second question is what is the timeout setting for authentication on the Meraki MX? We have not increased the timeout settings for the Meraki VPN policy in the radius server settings yet. Not sure if anyone has done this.
... View more
06-23-2021
11:45 AM
1 Kudo
Which Meraki switch is the equivalent of a CISCO Catalyst 2960-X 48 GigE POE switch? IS there a document somewhere that has comparisons between the two for different models?
... View more
07-28-2019
03:18 PM
The cisco router ports have only vlan 1 configured and are L3 ports. The Meraki switch ports are also access ports with native vlan 1. Has this been tested or confirmed to work by anyone?
... View more
07-28-2019
01:07 PM
Not sure if I should create a new discussion but is HSRP between 2 routers connected to a Meraki switch supported? The ports connected to the Cisco routers get unstable perhaps because of RSTP. When we connect a cisco switch in between the Meraki switch and the routers all seems to be fine.
... View more
04-29-2019
01:46 PM
Spanning tree on the cisco L3 switch keeps blocking the port. There is only only one link between the switches (no redundancy). However I have the switches connected like this CiscoL3_Switch -------- MErakiL3_Switch--------CiscoL2_Switch They all have vlan 1 and another vlan on the trunk ports.
... View more
04-29-2019
12:59 PM
I see a lot of issues in with spanning tree in a mixed cisco/meraki environment (majority being cisco). The meraki switches use RSTP and when cisco switches use PVST. Can Meraki switches be downgraded to PVST? WEcannot upgrade to PVST on the cisco switches. What is recommended in this scenario?
... View more
I agree but that was already done and we cannot quickly remediate this issue. And I honestly don't like that solution either because we have more vlans on that network that are not super scoped.
... View more
Anything I can do to get around this issue so that I'll have 2 ip addresses as gateway for 2 subnets in one vlan?
... View more
04-29-2019
07:41 AM
Hi, how do you configure a secondary ip address on an interface vlan on a Meraki L3 switch? WE have a superscope on a cisco network. With other words we have two /24 subnets on vlan 1. THe vlan 1 interface is configured with a primary and secondary ip address. Now we want to bring in a Meraki L3 switch to the routing in exactly the same way. Help is appreciated. Thanks.
... View more
My Top Kudoed Posts
| Subject | Kudos | Views |
|---|---|---|
| 1 | 3718 | |
| 1 | 3416 |
