Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
About goggel
Community Record
13
Posts
0
Kudos
1
Solution
Badges
Aug 11 2019
1:19 PM
Hi Spence Have you solved your issue? You can do this by removing NAT on the interface.
... View more
Aug 11 2019
1:01 PM
HI Is there any way of setting the primary uplink on an MX using API?
... View more
Labels:
- Labels:
-
Dashboard API
Jun 9 2019
4:55 PM
Hi Just discovered a way of solving this issue. I used NAT exceptions for the VLAN the device was conected to. That was the only way of getting this to work. If I turned of NAT on the interface that I do not want the client to connect trough the traffic stops. This is a new feature from version 15 as far as I know. I wrote a little bit more on my blog on this issue: networksandrants.wordpress.com/2019/06/09/limit-device-traffic-to-only-one-mx-uplink/
... View more
Jun 9 2019
4:45 PM
Hi Sorry for the late reply. Yes I'm trying to do it remotely. The issue is that the 2 routers are on 2 different locations and the router that I'm using atm is not under my control so it's an impossible solution for me 😞 Thanks for the suggestion!
... View more
May 29 2019
5:32 AM
I have connection on the port (green light) I can ping the router using the Uplink statistics function The WAN side of the router is down but as said the LAN side is up since I can ping it using uplink statistics. i just need to reach the router to change a setting to get it online again.
... View more
May 28 2019
3:57 PM
Didnt work. I think Flow Preferences are only valid if the link is Active or Ready.
... View more
May 28 2019
3:22 PM
Sadly it does not for some reason. It does not reply to ping or HTTPS. If I add the IP as a tracked IP in Meraki it responds, so it is very much alive.
... View more
May 28 2019
2:41 PM
Hi I have an MX65 where I have a dual WAN link. On my primary uplink I have a router that is not accesible from the outside world. The WAN link is only up un my secondary connection, is there any way of connecting to the router on my primary uplink? The router I'm trying to reach is on 192.168.1.1 so it is a private address. The WAN interface of that again is behind a NAT solution from my ISP.
... View more
Apr 29 2019
2:18 AM
Hi Thanks for the reply, it seems like it is not possible to block access to the second WAN connection. This connection is a sattelite connection also so the amount of bandwidth varies. This is so far the biggest drawback for me with Meraki :'(
... View more
Apr 26 2019
3:41 AM
Where can I create a deny rule in the firewall policy for a WAN connection. I'm not sure where I can firewall off 1 of the WAN connections.
... View more
Apr 26 2019
2:59 AM
But when WAN 1 is down the traffic will go to WAN2 if I understand correctly. I do not want the client to use WAN2
... View more
Apr 26 2019
2:44 AM
Hi I have an MX64 connected to the internet with 2 uplinks. One of them is a metered connection so I do not want client x to use the specified internet connection. But other clients can use both of them. How can I configure this configuration? I know you can do it with a cellular connection but I do not find it for Internet 1 and Internet 2
... View more
My Accepted Solutions
| Subject | Views | Posted |
|---|---|---|
| 5253 | Jun 9 2019 4:55 PM |
© 2025 Cisco Systems, Inc.
