Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Register or Sign in
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
About CHGR
CHGR
Comes here often
Member since Oct 26, 2018
Sep 18 2019
Community Record
24
Posts
0
Kudos
0
Solutions
Badges
Sep 10 2019
4:52 AM
please disregard my former message. i just need to use syslog for linux.
... View more
Sep 9 2019
7:20 PM
Thank you for your advice. I tried to get logging messages using some Syslog application. The logs I received didn't contain timestamps. <134>1 1568079752.579029350 Test_AP events type=disassociation radio='1' vap='0' Should I set up something on Meraki? Or, do I need to configure something on the Syslog application?
... View more
Sep 3 2019
5:17 PM
We are planning to provide guest access using Meraki MR. we are going to build a syslog server in order to get the information how long guests are using our network. 1) Could someone let me know which logs we need to send to syslog server to get to know what time guests start using and what time guests finish using our network. 2)Could someone show me the log above? 3)Does a syslog server need to assign a global ip address? Best regards,
... View more
Hello. I would like to know what if AP is rebooted during losing connection between cloud. AP doesn't have any configuration and clients can not connect to AP?
... View more
Dec 10 2018
5:33 PM
Hello. I was wondering if ping on client page is going from cloud to client? Is it correct? Or, is it pinging from AP to client?
... View more
Dec 10 2018
3:58 PM
Thank you for your reply. It was good to know when AP is rebooting its firmware was checked if it is the latest one.
... View more
Dec 6 2018
4:42 PM
Could someone let me know the boot sequence of Meraki MR? Farmware was installed at the first time that MR was connected to cloud, right? After that, MR always download their configuration except network setting when it is rebooting? There is nothing else happened during MR is rebooting?
... View more
Dec 5 2018
5:22 PM
Hello. Thank you for your advise. However, these 3 ip addresses doesn't work. I guess these are not allowed on our firewall.
... View more
Dec 5 2018
12:27 AM
Our AP is now connecting the internet via Proxy and Proxy sends DNS query to outside DNS server and it handle the name resolution curretly. AP can not connect outside DNS server directly and we configure ip address of internal DNS server in our AP and we configured internal DNS server provide lookup for meraki.com, google.com and yahoo.com. (Invers query was responded as server failure but support team said it's not related to the alart.) However, an alert message as "DNS is misconfigured" has always appeared on the Dashboard. Whatelse can we do for turning off this alert?
... View more
Nov 25 2018
8:43 PM
I would like to know how APs behave when they send a DNS query. In the case that APs send a query to DNS and get response which means it is succeeded, how long does AP wait for the next query? And also, in the case that APs send a query and it was failed, does AP keep sending a query every 15 sec?
... View more
Hello. Thank you for your reply. We must use proxy so we must keep using port 80 for communication between AP and Cloud. Is there any restriction for this communication which is like AP's firmware upgrade can not be done or some other? And, also isn't this communication safe at all because it is using port 80?
... View more
Hello. We have our own proxy server and APs and Cloud are communicating through it. We only see 80 port is used for communication between AP and Cloud even we open 7351, 7734, 7752 on our firewall. (We monitored it on firewall. ) I think Port 80 is a backup route and we get alert as Meraki communication is using backup route. Is this a proper way to communicate between AP and Cloud through proxy server?
... View more
Nov 12 2018
1:20 AM
I'm trying to access Meraki AP without DHCP. In that case SSID:meraki-setup can be seen and need to connect with this SSID. Then I can configure ip address for Meraki. However, I only could see SSID:meraki-scanning right now. Why did it happen? Should I do something else? I just connected Meraki to PoESW and did not configure anything on the port.
... View more
Nov 5 2018
9:30 PM
Hello. Could you correct me if I have misunderstood. Meraki MR supports WMM and WMM is function to prioritize the traffic. There is no way to change or I don't need to change dscp for 4 catefories of traffic as AC_vo, AC_vi, AC_be, AC_bk because Meraki AP will define which traffic belongs among AC_vo, AC_vi, AC_be, AC_bk and Meraki has already difine which traffic needs to be high priority. If I turn on "Enable default traffic shaping rules", WMM will start working. When I want to disable WMM, I need to choose "Disable default traffic shaping rules". Is it correct understanding? P.S. Aruba WLAN controller can change the dscp for WMM. So I got confused why Meraki can not change the dscp for AC_vo, AC_vi, AC_be, AC_bk.
... View more
I couldn't find any columns to set SNMP servers' IP address on Meraki. Where can I set it? Isn't it mandatry?
... View more
I want to set MCS value as 1-7,9-15. Does Meraki MR support to set this value? If so, could you let me know how to do it?
... View more
Nov 4 2018
9:44 PM
I have read Meraki MR supports WMM. Could you let me know how to enable/disable this function? Besides, I want to set WMM as below. WMM AC_vo --- dscp 56 WMM AC_vi --- dscp 40 WMM AC_be --- dscp 24 WMM AC_bk --- dscp 8 Could you let me know how to set it?
... View more
Nov 1 2018
11:19 PM
Thank you for your comment. Yes, It is. Now, we omited dynamic WEP among our options.
... View more
Oct 26 2018
6:10 PM
I totally agree with you. This is not my WLAN but someone another.
... View more
Oct 26 2018
3:38 PM
Hi, nwu1, Thank you very much for your advice. I opened a case in dashboad and got reply from Meraki support team. They said Meraki doesn't support dynamic WEP as you mentioned. All what I can do now is just using "make a wish". Cheers, CHGR
... View more
Oct 26 2018
12:20 AM
There was no mention of Dynamic WEP as an authentication in the Meraki's document. Is it applicable in Meraki MR? If so, could someone let me know how to configure it.
... View more
© 2024 Cisco Systems, Inc.
