Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Register or Sign in
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
About kev2five
kev2five
Comes here often
Member since Jun 20, 2023
Nov 12 2023
Community Record
18
Posts
0
Kudos
0
Solutions
Badges
Nov 7 2023
7:25 PM
MX Uplink IPs does use a VIP, the uplink communication uses the distinct non shared ip though.
... View more
Nov 7 2023
6:22 PM
Hi all, I've read the MX_warm_spare_-_high_avialability_pair document I understand to configure my static ip on my wan via the local status page. In all the examples it just shows the VIP address, where do I configure the distinct uplink IP and choose MX uplink IP? Thanks, Evan
... View more
Labels:
- Labels:
-
Firewall
Nov 7 2023
5:50 PM
Hi all, I have my opinion, but looking for any more reasons to add to my choice of which option to use when building my MX HA Devices. What is the most common choice? MX Uplink IPs or Virtual Uplink IPs? I think you get more redundancy of VRRP heartbeats if you use Virtual The seamless failover really only effects the cloud portal, anything else? Thanks in advance
... View more
Jul 16 2023
7:26 PM
The switch 'sent' data to the end device, the switch 'did not receive' any data back. Cool.
... View more
Jul 16 2023
6:19 PM
Hi all, I have a port that reports its 'no connected clinets on this port for selected time range'. I know the reason why. When I do a packet capture i only see broadcast/mcast traffic. The stats for packets is zero for received and populated for sent. Should this not be the other way around? Packets for the last 1 day Total Sent Received Rate Total 232,475 232,475 0 2 pkts/s (2 pkts/s ↑, 0 pkt/s ↓) Broadcast 110,441 110,441 0 1 pkts/s (1 pkts/s ↑, 0 pkt/s ↓) Multicast 122,034 122,034 0 1 pkts/s (1 pkts/s ↑, 0 pkt/s ↓) CRC align errors 0 0 0 - Fragments 0 0 0 - Collisions 0 0 0 - Topology changes 0 0 0 -
... View more
Jul 4 2023
9:56 PM
Painful having to constantly click on an object to refresh if a switch is active
... View more
Labels:
- Labels:
-
Other
Tested today, with and without vlan1. Without vlan 1 Meraki thought it was root. With vlan 1 Meraki was happy to say the catalyst core was root.
... View more
Hi, I'm planning to retain a Catayst Core running rpvst and keeping it as root. As long as I allow vlan 1 over the trunks to the MS switches will I have compatibility whilst retaining my current Catayst rpvst config? I got this from Meraki support: "If using PVST, this must only be running in VLAN 1 and the MSs should not be the root" From reference support documentation this seems clearer, in that I don't have to strip out other vlans from the rpvst configuration on catayst core: This is a Cisco proprietary protocol on Catalyst/Nexus switches that is compatible with spanning tree (802.1D) and RSTP (802.1w). It is important to note however that as Rapid-PVST is a multi-VLAN spanning tree protocol, MS series switches can participate in spanning tree only when a spanning tree instance is running on VLAN 1 of all switches. In addition, VLAN 1 must be allowed on all trunk ports running Rapid-PVST, so that BPDUs are seen by the Meraki switches in the topology. In this configuration, the MS series switches should never be the STP Root Bridge.
... View more
Jul 3 2023
1:30 PM
Thanks, I have tried that. My only option that is not greyed out once I tick a port, is édit', and this gives me the window to only change the description. Its a MS225-48LP switch.
... View more
Jul 3 2023
1:07 AM
Thanks for the swift reply. I've unsplit on my test switch, so thats good to know. I seem to have somehow put two ports on my test switch into Stack mode. How does one unstack these two? I seem to only have edit option>name. When reviewing switch stack page, it is empty. But on Switch Ports I have two listed as dedicated stack.
... View more
Jul 2 2023
9:09 PM
On my Meraki do I simply configure my desired two uplink ports with native vlan and allowed vlans. Then select them both and choose Aggregation. Then control the negotiation etc from my upstream Cisco Catalyst with matching configuration? Lastly, how to I take two ports out of aggregation on Meraki? Select both ports and ? Thanks
... View more
Labels:
- Labels:
-
Layer 2
Jun 22 2023
7:09 PM
Hi All, its due to using a Template. If I go into the template I can see the option. BUT, i don't want to apply this change to all my networks. So i'm asking support how I can target each switch across all my networks to receive the change in priority only. I have a suspicion i'll have to unassign from the template.
... View more
Jun 22 2023
3:19 AM
That was a good idea, I did switch_settings at the end, and it takes me to general
... View more
Jun 21 2023
1:59 PM
hmm, good point. I checked and out of none, read only and full. I have full
... View more
Jun 21 2023
3:24 AM
Thanks, When I hover on my Switch tab under a created network I get less options: Switches Switch ports Switch Stacks Dhcp servers/arp Routing and dhcp
... View more
Jun 20 2023
2:05 AM
This is all i see on this page. Its not clear, but I guess I click on ádd one' when I'm not configuring stacks on the network and then choose a single switch and change the priority? Switch stacks overview Configured stacks There are no configured stacks in this network. If you add one, we can help you configure it. Detected potential stacks No potential stacks detected
... View more
Jun 20 2023
1:00 AM
Hi , as per the documentation, i'm supposed to configure a root priority number on the 'switches/stacks' location. My dashboard has 'Switch Stacks', however I have no stacks and therefore no switches show up on this page. How do I set my root to be the core switch in this case?
... View more
Labels:
- Labels:
-
Other
© 2024 Cisco Systems, Inc.
