Community Record
14
Posts
23
Kudos
7
Solutions
Badges
Nov 19 2020
7:03 AM
1 Kudo
Hi @Eric_McClure Did you open a ticket with Meraki support ? I'm usually doing the same by staging spokes ahead but I dont remember the routes to be advertised before network being turned up However, I faced a similar issue on the hub side => when a hub was down, the route was kept in the routing table of all spokes leading to a blackhole situation After few discussions with Meraki, they activated a backend feature (has_track_peer_true_for_l3_vpn_hub_routes) to start tracking those routes and stop advertising them if the hub was down . They may have a similar feature for spokes
... View more
Nov 17 2020
9:40 AM
4 Kudos
Hi @DR1 I had the case last year, we set up a remote stacking between MS425 using MA-QSFP-40G-CSR4 and MPO12 Some former topics say that this is not supported by Meraki but here the details provided by my Cisco Solution engineer implying it is supported as their DAC / Stack cables are standard. SR4 and CSR4 are both MPO interfaces.
My recommendation would be that you will be ok with the MPO12
The document shows this but
Channel Pairs (Ethernet link Tx and Rx):
1 and 12 (Tx1 and Rx1)
2 and 11 (Tx2 and Rx2)
3 and 10 (Tx3 and Rx3)
4 and 9 (Tx4 and Rx4)
Channels 5, 6, 7 and 8 are unused I drafted quick specs after ends based on this first experience To note, I didn't follow up this project from start to end but they follow my initial recommendations and it ends up working fine. Cisco Spec slide about their QSFP-40G-SR I hope it helps. I'm pretty sure the same could be done with QSFP28. A similar discussion from last week https://community.meraki.com/t5/Managed-Services/MS355-long-distance-stacking/m-p/102794#M392 If you have access to a Cisco Solution engineer, you may ask him the fiber breakout specifications for MA-CBL-100G / 100GQSFP28 https://www.cisco.com/c/en/us/products/collateral/interfaces-modules/transceiver-modules/data_sheet_c78-660083.html https://www.cisco.com/c/en/us/products/collateral/interfaces-modules/transceiver-modules/datasheet-c78-736282.html https://meraki.cisco.com/lib/pdf/meraki_datasheet_sfp.pdf Edit: To confirm, MS425 Stack ports have been set to "stacking" so technically no different than a stack dedicated port on other series.
... View more
Nov 2 2020
9:27 AM
1 Kudo
Hi @JeremyBrainard That's the endpoint "claim network devices" where you set networkID in the URL and serial Number in the request body It will add the listed devices to the network https://developer.cisco.com/meraki/api-v1/#!claim-network-devices The other endpoint to claim order/devices into Organization dashboard is "Claim into Organization", which indeed claim the devices the first time into your dashboard https://developer.cisco.com/meraki/api-v1/#!claim-into-organization
... View more
Oct 7 2020
7:01 PM
3 Kudos
Hi @johnnyngena You can check the Meraki SFP datasheet, pretty useful document with all details to choose your SFP https://meraki.cisco.com/lib/pdf/meraki_datasheet_sfp.pdf
... View more
Sep 3 2020
8:19 AM
I got the same message on all my networks with MR74, simply solved by settings the external currently installed on them By default Meraki leaves it configured with MA-ANT-23 but seems to show the alert until you manually set the proper one as there are few possibilities Note you have to do it on both radios.
... View more
Sep 3 2020
7:39 AM
2 Kudos
Hi @GaryShainberg I think you will need to set WAN2 as primary link to do so.
... View more
Aug 19 2020
5:02 PM
2 Kudos
Hi @nikmagashi Indeed you figured it out: Shared secret field: it the shared secret to be configured on Windows VPN Client as well Secret field in Radius section: it the PSK/Secret to configure with Radius client on NPS server Regarding the IP Address to associate with the Radius Client on NPS Side, this meraki KB is really helpful and explains the different cases https://documentation.meraki.com/MX/Client_VPN/Configuring_RADIUS_Authentication_with_Client_VPN#Add_MX_Security_Appliance_as_RADIUS_clients_on_the_NPS_server On an intranet, If your MX uses a static route to reach out the NPS Server, you will have to use MX IP of network segment used by this route. If your MX relies on VPN tunnel to reach out NPS, use the MX IP of the highest-numbered VLAN Interface set "in VPN" I hope it helps
... View more
Jun 23 2020
5:01 AM
3 Kudos
If I remember correctly, the behavior is to pick the interface with the highest VLAN for radius trafic I remember I used to configure a dummy VLAN 1000 for this purpose
... View more
Jun 1 2020
1:25 PM
1 Kudo
Hi Jwiley78 I never tried on my side but i'm interested in checking that as well Have you ask Meraki to enable those as recommended in their documentation ? https://documentation.meraki.com/MX/Client_VPN/Client_VPN_Overview#Encryption_Method It seems though they only support AES128 and DH Group 5 (and only Group2 on Windows according to other discussion) https://community.meraki.com/t5/Security-SD-WAN/AES-256-encryption-broke-Client-VPN/m-p/78951#M19826
... View more
May 30 2020
9:08 AM
2 Kudos
When I was playing with MX68CW and Verizon SIM Card a while ago, I was able to make it work using Verizon APN "vzwinternet" As far as I remember, it was the only one stricly requiring an APN to make it work
... View more
Jan 14 2020
4:44 PM
Simply adding my feedback to this thread and confirming what have been said earlier as I'm facing similar issue since October. We have several devices that don't support WIFI6 at a point they dont even see our SSID being broadcasted but only neighbors SSID which is really odd to me (known issue on several intel chipset apparently) Meraki support did deactivate 802.11ax on both 2.4G & 5G Radios. However if you reboot the AP, 802.11ax is enabled back on 5G so you have to ask them to reapply the fix, time for their new 26.7 firmware to be released. Finally, you can end up with some Access Points with WIFI6 enabled on 5G and either not visible or creating issues with specific endpoints.
... View more
My Accepted Solutions
Subject | Views | Posted |
---|---|---|
6815 | Nov 17 2020 9:40 AM | |
1528 | Nov 2 2020 9:27 AM | |
1969 | Sep 3 2020 8:19 AM | |
1994 | Sep 3 2020 7:39 AM | |
2973 | Aug 19 2020 5:02 PM | |
3015 | Jun 23 2020 5:01 AM | |
9104 | May 30 2020 9:08 AM |
My Top Kudoed Posts
Subject | Kudos | Views |
---|---|---|
4 | 6815 | |
3 | 1290 | |
3 | 3015 | |
2 | 1994 | |
2 | 2973 |