Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Register or Sign in
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
About ZeeBoussaid
ZeeBoussaid
Getting noticed
Member since Jun 17, 2019
May 2 2023
Community Record
52
Posts
20
Kudos
3
Solutions
Badges
Feb 2 2022
9:07 AM
i dont think it is resolved, im looking at the latest MS15.9 and it still showing the Voice VLAN issue in the Known Issues:
... View more
Feb 2 2022
8:41 AM
i dont think the STP is the issue. we have STP enabled on all MS225 ports and after the 14.32 upgrade we started having issues on IP-Phones and laptops not authenticating. the "fix" for now is to roll back to 12.28
... View more
Feb 2 2022
8:37 AM
we are experiencing the exact issue with the ip-Phone trying to authenticate on VOice Vlan before the Data Vlan. the phones stop working after the laptop authenticate. i believe we have to roll back to 12.28 until Meraki fix this issue.
... View more
Jan 11 2022
8:07 AM
apparently this feature is not available yet on MS switches which is mindboggling, on the cat switches i could set a ipv6 DHCP snooping command to block. at this point it seems the only "fix" for my issue the only way to block that traffic would be to configure an IPv6 ACL on my switches.
... View more
Jan 11 2022
5:10 AM
good morning, im not sure if this topic was discussed before, if it was I apologize in advance, can anyone explain\show me how to block ipv6 DHCP servers on Meraki MS225 running on MS12.28? Thank you!
... View more
Oct 26 2021
11:30 AM
@RizkiMuhammad do you guys use ISE for authentication? if so, is this MR36 added to ISE with the correct static IP. the reason im asking because in my case, clients were getting 0.0.0.0 IPs, Meraki support could not figure it out, so we rebooted radius server and everyone connected just fine afterwards.
... View more
Oct 20 2021
10:57 AM
@dwash in the Meraki dashboard, go to Wireless-> Configure-> Firewall & Traffic Shaping. I think you can set rules and limit the bandwidth per SSID. under Default Rules you should see an option for Software update.
... View more
Oct 20 2021
4:22 AM
I think the problem is ISE itself, check your last patch. we rebooted the 2 ISE radius servers and that seems to fix the issue.
... View more
Oct 19 2021
5:35 AM
@JSalmond I have a ticket open with Meraki Support, they refer it to their Cisco TAC team, Meraki doesn't even know what the error showing in ISE means. the weird thing is, the MR33 that I initially had an issue with is now working, clients are getting IPs and authenticating correctly. yesterday I added a new MR42 in our HQ and I successfully connected to it at the beginning and then it dropped, my laptop won't get an IP. if you have multiple people unable to connect and it's a big deal, try to set the SSID with a PSK and no splash, it will bypass ISE temporarily. share the SSID password with your clients so they can connect while you can troubleshoot this.
... View more
Oct 4 2021
10:49 AM
@cmr that's actually a good test to assign the port on the MX to truck with native 100. im just confused why out of 200 MRs this one refuses to work. i can use the Vlan tagging and assign Vlan 100 just for the sake of testing. i also get the error below in ISE, looks like a bottleneck somewhere. Event 5441 Endpoint started new session while the packet of previous session is being processed. Dropping new session. Failure Reason 5441 Endpoint started new session while the packet of previous session is being processed. Dropping new session.
... View more
Oct 4 2021
5:03 AM
@cmr the MR is connected to port 4 on the MX, in bridge mode. port 4 on the MX is set to access Vlan100. Meraki is unable to figure this out, and asking to troubleshoot it in real time.
... View more
Oct 1 2021
10:32 AM
@ckmiller the Alert Management feature is out of Beta in MX15.44.
... View more
Oct 1 2021
4:32 AM
2 Kudos
@harmankardon i would say about a year and half since we went with SD-WAN and MX67. so as you can imagine, management was not happy about this scenario since i pushed for Meraki. it could be a bad batch no clue, but the RMA went smooth and so was the replacement, no configuration change was made, the new MX will only need internet access through WAN1 to get the current config, you should be good to go after that. in my case i use 2 uplinks, and both are static, so i need to configure the new MX before deployment, but like I mentioned if you have your MX in DHCP, you should be able just to plug and play, the new MX will get the current config from the dashboard.
... View more
Oct 1 2021
4:25 AM
@PhilipDAth: the MR is connected to an MX67 via port 4, and VLAN is allowed in that port, I already checked, but for some weird reason, under Clients in the MX, the only device im testing to connect to the MR, is showing VLAN0, but the allowed VLAN is 100. I dont think it's a DHCP scope issue since only about 10 employees in the office in question.
... View more
Sep 30 2021
9:13 AM
that's not the same issue, all my MRs have static assigned, the clients who are not getting a valid IP.
... View more
Sep 30 2021
8:42 AM
we have about 200 MRs some are 42 and most are 33. recently I start receiving calls about users unable to connect to to some MR33. no changes were made and i know other MR 33 in our network are working just fine. the MR in question is showing users with 0.0.0.0 IPs, Radius servers are configured correctly since these MRs were bounded to a template when first deployed. i checked ISE and the NAD is sending incomplete authentication requests often in the same millisecond. I don’t know how ISE is supposed to process them that fast i reboot it couple times, even removed it from ISE and add it back and still unable to figure this out. firmware is up-to-date 27.1.1. any thoughts? thank you in advance. Cheers.
... View more
Sep 29 2021
4:35 AM
2 Kudos
The APN hard code did not work, Meraki support was able to fix the LTE issue on some 50 MX, but was unable to fix about 40 MX, so they deemed them deflective and ultimately RMA'd them. no issues reported after the new MXs were installed.
... View more
Jun 18 2021
10:49 AM
hello, im not sure if you have Insight, if you do, hover over it and under Configure click Alerts, once there you should be able to add alerts for WAN1 and WAN2 and assign which emails will receive the alerts, you can also set a threshold. i have been using this feature (still in Beta) for quite some time and it's awesome.
... View more
Apr 28 2021
11:31 AM
1 Kudo
I thought the MX 16.2 release suppose to add LTE support to be used as un uplink instead of only being used for failover.
... View more
Apr 28 2021
10:29 AM
1 Kudo
I forgot to mentioned that the WOL option needs to be enabled on the LAN adapter prior to send it via Meraki dashboard. I tested it on my test laptop and it worked like a charm.
... View more
Apr 28 2021
10:14 AM
2 Kudos
I just want to share something and im not sure if it was discussed before but it’s a tool nevertheless. On Meraki dashboard you can actually send a Wake on Lan packets to reboot a machine that is offline. The caveat is the HDD encryption password needs to be disabled on the machine if exists. I just thought it’s cool to be able to do that via Meraki Dashboard.
... View more
Apr 6 2021
5:56 AM
2 Kudos
Meraki was aware of the issue, I opened a case with them and the issue seems to be resolved as others in this platform confirmed.
... View more
Apr 6 2021
5:23 AM
contacted Meraki and they were aware of it. it seems to be fixed now. it's just annoying when you try to reconfigure the Uplinks and realize you can't.. but it's fixed nevertheless and im connected to N297 btw.
... View more
Apr 6 2021
4:23 AM
1 Kudo
does anyone has encountered this error on their dashboard. the MX uplink tab will only show ""Uplink Tab failed to load" on every MX in our organization.
... View more
My Accepted Solutions
| Subject | Views | Posted |
|---|---|---|
| 3151 | Apr 6 2021 5:23 AM | |
| 1949 | Mar 8 2021 10:24 AM | |
| 1644 | Nov 18 2020 9:15 AM |
My Top Kudoed Posts
| Subject | Kudos | Views |
|---|---|---|
| 2 | 5100 | |
| 2 | 5156 | |
| 2 | 7395 | |
| 2 | 966 | |
| 2 | 18421 |
© 2024 Cisco Systems, Inc.
