Documentation Digest: February 23rd - March 1st

Hannah-C
Meraki Employee
Meraki Employee

Documentation Digest: February 23rd - March 1st

DocDigest_Banner.png

 

 

New articles:

Meraki SDWAN 'HUB' Integration with Secure Connect

Change: New article.

 

MX:

MX Sizing Guide & Principles

Change: Added "Maximum Number of AnyConnect Sessions" to Feature Specific Data; added "Advanced Security Throughput (Prevention) EMIX" to Performance Data; updated Performance Data table; added note for Advanced Security Throughput Tests with "IPS Mode in Detection or Prevention configuration".

 

Dynamic DNS (DDNS)

Change: Added "If DDNS is in use with an HA pair configured with a virtual IP (VIP) behind NAT, DDNS will resolve to the NAT-translated (public) address of the management/uplink IP, rather than the NAT-translated virtual IP."

 

Trusted Traffic Exclusions

Change: Added sections "How are my applications identified?" and "Trusted Application Category List".

 

MX Routing Behavior

Change: AMP Registration and File disposition will adhere to the route priority.

 

VPN Full-Tunnel Exclusion (Application and IP/URL Based Local Internet Breakout)

Change: Added "Traffic sourced from the MX itself will not adhere to VPN exclusion rules".

 

MS:

Getting started: Cisco Catalyst 9300 Management with Meraki Dashboard

Change: Added new C9300L and C9300X models; added firmware requirements for all C9300X, C9300 and 9300L switches (IOS-XE 17.9.3m3).

 

Catalyst 9300-M Datasheet

Change: Updated Forwarding rate for C9300-24S-M and C9300-48S-M.

 

Switch Stacks

Change: Added note "Based on the number of members in a stack, the switch stack may require approximately one hour to become operational and connect to the Meraki Dashboard".

 

MS Switch Access Policies (802.1X)

Change: Added note "VLAN Profiles feature simplifies VLAN management across multiple sites by enabling dynamic assignment of VLANs based on descriptive names rather than numerical IDs. This facilitates easier management across multiple sites with varying VLAN configuration reducing the need for multiple RADIUS policies."; added descripton for "Increase Access Speed"; added references to C9300-Ms.

 

MR:

Channel Bonding

Change: Added note that while achieving higher PHY rates in 2.4GHz is theoretically possible, it requires using 40MHz channels (20 + 20 MHz channel bonding) in 2.4GHz, which Cisco Meraki does not enable because this feature is not recommendable in real-world enterprise deployments.

 

Wi-Fi Personal Network (WPN)

Change: Removed the "2x SSIDs per Meraki dashboard network" scalability limit for the iPSK without RADIUS Authentication Type.

 

CW9163E Installation Guide

Change: Added "CW9163E only supports mesh at 2.4 and 5 GHz".

 

MV:

Motion Search and Motion Recap

Change: Added note that Motion Detector v1 is currently only supported on MV21/71. For all other cameras, Motion Detector v2 is set as the default on MV5.5.1+ and Motion Detector v1 is deprecated.

 

Meraki Vision Portal Changelog

Change: Added release notes for up to v1.17.3.

 

General Administration:

Cisco Meraki Canada Region

Change: Added note that Cloud Monitoring for Catalyst is currently not supported in the Meraki Canada Region.

 

Small-Form Factor Pluggable (SFP) and Stacking Accessories

Change: Added MA-SFP-10GB-LRM as compatible for MS390/C9300.

 

Creating and Applying Group Policies

Change: Added note "When doing a Configuration Sync to multiple target SSIDs, disable group policy assignment by device type before doing the sync".

 

MV Presence Analytics

Change: Added "Area occupancy with duration" for MV2, MV12, MV22, MV32, MV52, MV72.

 

MT:

MT12 Datasheet - Water Detection

Change: Added accessories. External Power Adapter (Sold Separately): MA-PWR-USB-US, MA-PWR-USB-UK, MA-PWR-USB-EU, MA-PWR-USB-AU, MA-PWR-ETH (USB-C to Ethernet adapter).

0 Replies 0
Get notified when there are additional replies to this discussion.