Register or Sign in
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
- About ZachM90
ZachM90
Comes here often
Member since Jan 3, 2019
08-05-2019
Community Record
7
Posts
0
Kudos
0
Solutions
Badges
05-02-2019
05:49 AM
Thanks for the replies guys, i did have the routes pointing back to the MX configured on our L3 peer. I wanted to get something in place for this morning so I went ahead and enabled OSPF. I've got my adjacency up and all is well now. The troubleshooter in me wants to roll back and find what the issue was statically but I think we're going to press forward since this was the ultimate goal to get to anyway. Cheers, Zach
... View more
05-01-2019
05:21 PM
I believe so, under addressing and vlans -> LAN config i have the subnet defined and the MX IP as the IP ending in .10. Also just to add another note, i've got a static route for the remote subnet defined on the data center L3 device pointing back to the MX so the return traffic should be covered as well. Seems like i'm just missing something on the MX itself because I cannot ping 10.106.210.1 from the MX.
... View more
05-01-2019
04:34 PM
We are using an MX84 as a VPN concentrator for our remote Z3, Z3C, and other MX's in the field. These remote devices have local subnets configured on them that are currently unreachable from our data center. The remote devices and the MX are up on the dashboard and the VPN between them is functioning as well. Where I'm getting stuck is what sort of static route i would need to configure on the MX84 so that the remote subnets can communicate with the data center and vice-versa. The MX84 is using an IP address of 10.106.210.10 and the upstream L3 device in the data center that contains our core subnets is 10.106.210.1. I tried configuring a static route of 0.0.0.0/0 pointing to 10.106.210.1 on the MX but that does not seem to work. We're still in a proof of concept stage and do plan on using OSPF between the MX and our Core but would like to have at least one Z3 functioning using static routes for now. Thanks!
... View more
01-04-2019
06:40 AM
Thanks Brecht, I saw that note as well. So far it seems that may not be the case, we have added some clients to a whitelist in Network A and you can filter to show them as "Clients with a policy." but when you move over to Network B under the same template you do not see those clients. What im curious to test is if we have that client added to Network A actually connect to the SSID at network B and that'll populate them in the client list with the applied policy. Appreciate the replies! Zach
... View more
01-03-2019
11:44 AM
What we have is a guest SSID that we broadcast at all of our branches. For certain clients that connect to this SSID, we whitelist their MAC so they can skip authentication. We want to sync this whitelist to all branches so no matter which branch the whitelisted client is at, they'll pass through instead of authenticating.
... View more
01-03-2019
10:03 AM
Thanks for the reply Philip, all of our branch networks are bound to a single template but the issue here seems to be that you can only whitelist clients under a specific network, not the template itself. So initially the whitelist is only applied to network A and no other networks in that template. That's where I was hoping the configuration sync tool would come into play but as my original post indicated that doesn't seem to be working. Do you know of a way to whitelist devices within a template so that it would push out to all networks bound to that template?
... View more
01-03-2019
09:54 AM
Hello, I'm running into an issue when trying to use Configuration Sync. To briefly summarize our configuration we're only using Meraki for our wireless solution. All networks that have been created have been created using two different templates. All networks are marked as wireless and not combined. We have a need to whitelist certain clients per SSID and want to sync that whitelist to all networks under a single template. When i navigate to Organization -> Configuration Sync I'm only given the option to select the template as the source network and my only option under target network is set to All. When filling out those requirements the page updates but does not give me the option to copy over any configuration from source to destination. (See Screenshot below for clarity). I guess I'm looking for some advice on what I'm doing wrong or if there is a better way to copy a whitelist from one network to another. Thank you.
... View more
