I'm assuming as he IPads lost network connectivity (switched off before SM update pushed) the only way for them to get updated with the SM updates would be to rejoin a network of some sort. Therefore the only logical option would be to manually enter the new pre-shared key to re-associate to the network. ... View more

Nope - if you've tried a factory reset and a different PoE port it appears to point to a dead AP. Give meraki support a ring, see if they can get onto the AP, if not they'll happily RMA the faulty AP. ... View more

You can't do warm spare at a switchport level with MS switches, only at a Switch level. ... View more

Hello @ahmadtat; Welcome to the community! You're post is a little confusing. However, my recommendation is to look into 802.1x intergration with AD - This assumes you are using a full stack Meraki deployment. - This assume that the respective users would log-out from the machine before finishing their shifts. ... View more

Phillips got it sorted! ... View more

if not configuration has changed on the MX and this behaviour has started, I wouldn't start to fiddle around with settings. I'd give Meraki support a call and reproduce the issue - They have elevated rights to get onto the box and see if this is a bug/caching issue with the MX.   If you'd rather try just fixing the issue yourself - try by starting a reboot of the device after hours - Clearing any cache that may have caused the problem. ... View more

Short answer from my assumption is No. The MX line integrates with Cisco ISE to provide identity services  it would not be able to replace it. ... View more

Hello @Jklein, I'm a little confused by your post. In theory if your using HA for MX redundancy and VRRP for MS Redundancy you could use multiple switchport to multiple NIC's in the servers to provide redundancy. - I hope this makes sense. ... View more

Hello @Jklein, You question is a little confusing - Do you mind expanding? The Firewall range of Meraki (MX) all natively support SD-WAN features therefore there is no need for a ASX device to perform SD-WAN. ... View more

Hello @Jklein To my knowledge none of the MS line supports Cisco TrustSec. ... View more

Hello @Bill,   This would indicate an issue with UDP hole punching mechanism used to establish VPN connectivity. Please refer to the following article for more information and resolution steps - https://documentation.meraki.com/MX-Z/Site-to-site_VPN/Troubleshooting_VPN_Registration_for_Meraki_Auto-VPN ... View more

You could try and take a packet capture from the LAN side of your Meraki device to ensure that there is differently not an IP Conflict issue. Trying rebooting your Meraki device to clear any ARP cache or alternatively you may have to wait for it to clear itself.   You could also attempt clearing the client usage data (If you're using an MX device) by following this guide - https://documentation.meraki.com/MX-Z/Monitoring_and_Reporting/Clearing_client_usage_data_on_the_MX_Security_Appliance ... View more

Must be a simple feature to enable then 🙂 ... View more

I don't have an idea. I'd recommend using the "Make a wish feature" within dashboard and also reaching out to your local Meraki sales rep if you have sales opportunity which is pending on this feature. ... View more

As-well as configuration templates you could also use configuration sync - https://documentation.meraki.com/zGeneral_Administration/Templates_and_Config_Sync/Cloning_Network_Settings_with_Configuration_Sync ... View more

Both of the above should work. I've included a link here to a article outlining configuration sync in more detail - https://documentation.meraki.com/zGeneral_Administration/Templates_and_Config_Sync/Cloning_Network_Settings_with_Configuration_Sync ... View more

I'd also like some of these feature's included especially the option for off cloud storage integration.   I'd suggest utilising the "Make a Wish" feature in dashboard and also reaching out to your local sales rep to express your needs for these features, especially if you have potential deal optifnities which could be pending these required features.  ... View more

I'm going to say that this is probably a limitation from "Lithium".  However, it is extremely ironic and should be a simple feature to include. I'm also stunned how this was not taken into consideration from get go. ... View more

Hello @Ashraf,   Meraki AP's come with "Air Marshall" which utilises the extra scanning radio within Meraki AP's to scan for any wireless security threats within your wireless network. Please refer to the following article for more information - https://documentation.meraki.com/MR/Monitoring_and_Reporting/Air_Marshal.   Regarding the coverage provided by MR34's please refer to the MR34 datasheet which outlines the RF performance characteristics - https://meraki.cisco.com/lib/pdf/meraki_datasheet_MR34.pdf ... View more

Hello @Al, by the description of your issue it appears that your cellular provider may require a custom APN for the Meraki device to be able to register the dongle. - Please refer to the bottom of the following Meraki support article - https://documentation.meraki.com/MX-Z/Cellular/3G_-_4G_Cellular_Failover.   My recommendation would be to reach out to your cellular provider to find out the 'APN' required and then opening a support case with Meraki support to pin the APN to your Z1 device. If this doesn't fix your issue I'm sure Meraki support will be able to assist you with troubleshooting the connectivity issues from there on-wards.  ... View more

The only other solution to this would be to seperate the Network into a MR and MX network individually (Not combined) and only setup syslog on the MX network?  ... View more

Yes to both of your questions. There are however some features which are not available when putting the MX into Passthrough mode. Refer to the following article for more information - https://documentation.meraki.com/MX-Z/Networks_and_Routing/Passthrough_Mode_on_the_MX_Security_Appliance_and_Z1_Teleworker_Gateway ... View more

Hello @firstclick, The MX's can be put into bridge mode by navigating to Security appliance>addressing & Vlans and choosing "Passthrough or VPN Concentrator mode".   This will ultimately put the MX into layer 2 bridging mode.  ... View more

Meraki switches are compatible with any vendor AP's (assuming they use industry standard protocols)  - To answer your question; Yes the Cisco AIR-AP1131AG-A-K9 is compatible with Meraki switches.   For Management (Configuration) you will be unable to manage and configure the Cisco AIR-AP1131AG-A-K9 from the Meraki dashboard and will therefore have to use it's respective management/configuration platform. ... View more