MS 14.28 RC Firmware Out

Mloraditch
Building a reputation

MS 14.28 RC Firmware Out

Alerts

  • MS390 upgrades to this version will experience a full system reload

Branch additions

  • Syslog support for MS390 series switches
  • SNMP support for MS390s
  • RADIUS accounting support for MS390s
  • Alternate Management Interface support for MS210/MS225/MS250/MS350/MS355/MS410/MS425/MS450 series switches
  • QoS support for MS390s
  • CoA support for MS390s
  • STP anomaly detection events for non-MS390 series switches
  • Adaptive policy support for MS390 series switches
  • SecureConnect support for MS210/MS225/MS250/MS350/MS355/MS410/MS425/MS450 series switches

Bug fixes

  • L3 stack stability improvements
  • In very rare circumstances, MS220/320/420 series switches would encounter boot loops
  • In rare instances, redundant links on stacks can incorrectly stay in a forwarding state if a stack member is rebooted
  • In rare circumstances, the next hop VLAN is incorrectly modified for existing OSPF SVIs when a new SVI is added which will also participate in OSPF. A reboot will correct this (present since MS 11)
  • A high amount of constant STP TCNs in a network may result in instability, and in rare instances, switch crashes
  • Default SGTs are missing from the Adaptive Policy configuration
  • Deconfiguring Adaptive Policy could result in the switch going offline
  • IPv6 router advertisements sent by unicast to the link-local address are missed
  • In rare instances, when a stack reboots, ports may come up as "LACP blocked state", even if LACP is not configured (present since MS 10)
  • In rare instances, non-MS390 switches will reboot (present since MS 12)

Known issues

  • In large layer 2 networks, MS390s may drop ARP packets if there is an excess of 500 ARP packets per second
  • In rare instances, a switch stack member may reboot
  • MS390 ports are limited to the lowest link speed since boot if QoS is enabled
  • In rare instances, non-MS390 switches will reboot (present since MS 12)
  • MS120s may show PoE usage on the incorrect port
  • In rare instances, a stack member may go offline until rebooted (present since MS 12)
  • In rare instances, non-390 stack members will reboot (present since 12.29+)
  • Packet loss is observed when pinging the MS390 management IP
  • MS120s on rare occasions will reboot (present since MS 11)
  • Stackpower is not enabled on MS390s by default
  • Broadcast types of traffic can leak into the Guest VLAN if a port that fails authentication has a Voice VLAN configured, and dashboard has a Guest VLAN defined (present since MS 11)
  • Links being established on a MS120 can result in neighboring ports to flap (present since MS 11)
  • MS120s with multiple access policies enabled may reboot when port changes are made
  • MS390 - Port Up/Down Events Shown Across All Members
  • Clients connected to a trunk port on the native VLAN will show "native" for the VLAN information rather than the native VLAN ID.
  • Enabling Combined Power on MS350/355 switches results in events being logged once per minute (present since MS 11)
  • Networks containing a large number of switches may encounter issues saving changes on the Switch Settings page
  • Stack members are not being marked to update their configuration when changes are made on other members
  • mGig switches will have an amber light for all physical ports that do not negotiate to the highest supported speed. Dashboard will continue showing a light green status for all ports above 100Mbps. Example, MS355 switchports will incorrectly show an amber light for 1G, 2.5G, and 5G, but will show a green light for 10G.
  • The list of switches to clone from fails to load when cloning a switch in an organization with a large number of switches and networks
  • MS120s switchports with MAB authentication may randomly deauthenticate clients. In order to resume client authentication on that port, a switch reboot is required (present since MS 12)
  • MS390 stacks on rare occasions will require a manual reboot after the upgrade has completed
  • MS390 series switches do not support SM sentry
  • MS390 series switches do not support Meraki authentication
  • MS390 series switches do not support URL redirection
  • MS390 series switches do not support MAC whitelists
  • MS390 series switches do not support loop detection
  • MS390 series switches do not support warm spare/VRRP
  • MS390 series switches do not support UDLD
  • MS390 series switches do not support MAC flap detection
  • MS350-24X and MS355 series switches do not negotiate UPoE over LLDP correctly (predates MS 10)
  • Rebooting any MS390 stack member via the UI will result in the entire stack rebooting
2 REPLIES 2
Mloraditch
Building a reputation

Gotten notices that it was pushing to over 50 networks at various revs in the past hour

cmr
Kind of a big deal
Kind of a big deal

We got bitten by this one:

 

  • In rare instances, redundant links on stacks can incorrectly stay in a forwarding state if a stack member is rebooted

Fortunately we use a separate physical link for management so it was simple to recover, glad it has been fixed though 😎

Get notified when there are additional replies to this discussion.
Welcome to the Meraki Community!
To start contributing, simply sign in with your Cisco account. If you don't yet have a Cisco account, you can sign up.
Labels